Profile SF720 User Manual
Page 2
I
NTRODUCTION
1
P
ARTS
LIST
TEMPLATE
SPEAKER WIRES
LENGTH: 3m (9’ 10”)
RETAINING CLIPS
MOUNTING
SCREWS
SIZE: 4 x 25mm
SF720
Speaker
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 x 7” 2-Way
Woofer Cone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Carbon Polypropylene
Tweeter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1" Titanium Dome with Neodymium Magnet
Surround . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Butyl Rubber
Maximum Input Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 160 Watts
Nominal Input Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5~60 Watts RMS
Impedance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Ohms
Magnet Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Oz.
Sensitivity. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92 dB/W/m
Frequency Response . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 ~ 22,000 Hz
S
PECIFICATIONS
Congratulations on your purchase of a Profile state-of-the-art speakers. Your selection of a
Profile car audio product indicates a true appreciation of fine musical reproduction. Whether
adding to an existing system or including your Profile speakers in a new system, you are certain
to notice immediate performance benefits.
Before mounting the speakers, select a location that allows for at least 58mm (2 1/4”) of
mounting depth for top mount or 68mm (2 5/8”) of mounting depth for bottom mount. The
speaker inside the door must not come in contact with the window when rolled down.
Additionally, the speaker should be out of the way of torsion bar springs, window cranks and
door handles allowing for normal operation.
SPACERS
I
NSTALLATION
CONNECT SPEAKERS.
MOUNT SPEAKERS.
DOOR MOUNT
REAR DECK MOUNT
VEHICLE’S FACTORY GRILLE
(NOT INCLUDED)
2
SF720
TO RADIO OR AMPLIFIER
TO RADIO OR
AMPLIFIER
BLACK
STRIPED WIRE
SOLID
COLOR WIRE
BEFORE STARTING YOU WILL NEED TO DETERMINE
IF YOU HAVE FACTORY LOCATIONS WITH CUTOUTS
AND PRE-DRILLED MOUNTING HOLES. IF SO, SKIP TO
STEP . IF NOT, USE THE ENCLOSED TEMPLATE TO
MARK THE AREA TO CUT AND DRILL HOLES.
INSERT RETAINING CLIP OVER HOLE
ON THE REAR DECK OR IN DOOR PANEL.
PLEASE NOTE: IF YOU ARE REPLACING
FACTORY SPEAKERS, YOU DO NOT NEED
TO USE THESE CLIPS AND YOU SHOULD
USE THE FACTORY SCREWS TO MOUNT
THE SPEAKERS.
IMPORTANT!: THE SMALLER SPILT HOLE
ON THE CLIP SHOULD BE ON THE TOP
SIDE OF THE REAR DECK AND THE
LARGER HOLE SHOULD BE ON THE
BOTTOM SIDE (TRUNK SIDE) OF
THE REAR DECK.
3.3mm (5/32”)