Life Fitness UT4 User Manual

Page 6

SSEMBLING THE

PRIGHT

XERCISE

IKE

Tools Required: Metric Wrench Set, Metric Allen

Wrench Set, Phillips Screwdriver

1. Locate and install the two LEVELER FEET (A) to the

bottom of the REAR STABILIZER (B).

2. Attach the REAR STABILIZER (B) to the BASE UNIT

from the top of the REAR STABILIZER BRACKET (D)

and two 13/16" BUTTON HEAD SCREWS (2) from the

front side of the REAR STABILIZER BRACKET.

Tighten the SCREWS securely.

3. Locate the MONOCOLUMN (E). Insert the WIRE (F)

leading from the SIDE ACCESS HOLE (G) of the

MONOCOLUMN fully into the MONOCOLUMN.

Remove the GROMMET (H) from the SIDE ACCESS

HOLE and set it aside.

4. Slide the MONOCOLUMN COVER (J) onto the

MONOCOLUMN (E) as shown. Slide the MONOCOL-

UMN COVER up to the HANDLEBAR TUBE (K).

5. Re-insert the GROMMET (H) into the SIDE ACCESS

HOLE (G) of the MONOCOLUMN (E). Pull the WIRE

(F) back out through the SIDE ACCESS HOLE.

6. With the HANDLEBAR TUBE (K) facing the rear of the

unit as shown, slide the MONOCOLUMN (E) into the

MONOCOLUMN BRACKET (L) of the BASE UNIT (C).

Slide the MONOCOLUMN down until it is fully seated.

Secure the MONOCOLUMN to the MONOCOLUMN

BRACKET using two 3-15/16" HEX HEAD BOLTS (3)

and three LOCK WASHERS (4) (as shown) from the

rear side of the MONOCOLUMN and two 2-3/8" HEX

HEAD BOLTS (5) and LOCK WASHERS (4) from the

user left side of the MONOCOLUMN BRACKET.

Tighten the BOLTS securely.

CAUTION: BE CAREFUL NOT TO PINCH THE

WIRE (M) LEADING FROM THE MONOCOLUMN

BRACKET (L) WHEN INSERTING THE MONO-

COLUMN (E) INTO THE MONOCOLUMN

BRACKET.

7. Connect the WIRE (M) leading from the MONOCOL-

UMN BRACKET (L) to the corresponding WIRE (F)

from the SIDE ACCESS HOLE (G) of the MONOCOL-

UMN (E). Slide the MONOCOLUMN COVER (J)

downward to the meet the MAIN SHROUDS (N).

Secure the MONOCOLUMN COVER to the MAIN

SHROUDS using four 1/2" PHILLIPS SCREWS (6)

and matching FLAT WASHERS (7). Tighten the

SCREWS securely. Do not overtighten the SCREWS.

8. Locate the SEAT POST CAP (O). With the curved side

facing upward toward the SEAT (P), slide the SEAT

POST CAP over the SEAT POST (Q).

9. Locate and slide the SEAT POST SPACER (R) over

the end of the SEAT POST (Q). Using two 1/4"

PHILLIPS SCREWS (8), secure the SEAT POST

SPACER to the end of the SEAT POST. Tighten the

SCREWS securely.

10. With the nose of the SEAT (P) facing forward, insert

the SEAT POST (Q) into the SEAT POST SUPPORT

(S).

11. Begin inserting the SEAT ADJUSTMENT KNOB (T).

Lift upward on the seat and seat post until the seat

post locks into a position. Insert the 5/16" PHILLIPS

LOCKING SCREW (9) and tighten securely.

12. Slide the SEAT POST CAP (O) downward to meet the

top of the SEAT POST SUPPORT (S). Secure the

SEAT POST CAP to the SEAT POST SUPPORT using

two 1/2" PHILLIPS SCREWS (6). Tighten the

SCREWS securely. Do not overtighten the SCREWS.

13. Remove the DISPLAY CONSOLE (U) from its shipping

carton. Position the above the DISPLAY CONSOLE

BRACKET (V). Connect the CONNECTOR (W) lead-

ing from the DISPLAY CONSOLE BRACKET to the

corresponding jack located on the back of the DIS-

PLAY CONSOLE. Secure the DISPLAY CONSOLE to

the DISPLAY CONSOLE BRACKET using four 1/2"

PHILLIPS SCREWS (6). Tighten the SCREWS

securely. Do not overtighten the SCREWS.

14. Locate the HANDLEBAR ASSEMBLY (X). With the

handlebars facing forward, position the HANDLEBAR

ASSEMBLY near the top of the HANDLEBAR TUBE

(K). Slide the HANDLEBAR ASSEMBLY fully into the

HANDLEBAR TUBE. Secure the HANDLEBAR

ASSEMBLY to the HANDLEBAR TUBE using four 5/8"

BUTTON HEAD SCREWS (10) and matching FLAT

WASHERS (11). Tighten the SCREWS securely.

15. Locate the PEDALS. Install the RIGHT PEDAL (Y)

(marked with an "R") to the USER RIGHT CRANK

ARM (Z). Repeat for the LEFT PEDAL (AA) (marked

with an "L").
NOTE: THE LEFT PEDAL (Y) HAS REVERSE

THREADS.

16. Locate the WATER BOTTLE BRACKET (BB). Secure

the WATER BOTTLE BRACKET to the underside of

the HANDLEBAR TUBE (K) using two 3/8" PHILLIPS

SCREWS (12). Tighten the screws securely. Insert the

WATER BOTTLE (CC) into the WATER BOTTLE

BRACKET.

17. Position the unit in the desired location for use. The

unit can be easily moved into place by lifting the rear

of the unit and rolling it on the front rollers. Level the

unit before use. Refer to the leveling instructions stat-

ed in the operations portion of this manual.