Linear HCI+2 - Manual

HCI+2
2-Foot Rail Extension
For Use with HCI-12 12-foot “I-beam” Rail
Installation Instructions
1. PRODUCT DESCRIPTION
The Model HCI+2 2-foot “I-rail” extension is designed to be compatible with
the Model HCI-12 12-foot chain-drive “I-rail” used in commercial garage door
installations and in carriage house garage door installations. The 2-foot extension,
when added to the 12-foot “I-rail”, provides a 14-foot long rail for operating high-lift
doors.
The kit includes two “T-rail” sections that bolt together to form an “I-rail” and
connect to the main “I-rail” using two reinforcing straps. The kit also includes two
short lengths of chain to extend the stock chain at the turnbuckle.
2. KIT CONTENTS 3. LOOSEN AND DISASSEMBLE TURNBUCKLE
USA & Canada (800) 421-1587 & (800) 392-0123
(760) 438-7000 - Toll Free FAX (800) 468-1340
www.linearcorp.com
PRINTER’S INSTRUCTIONS:
INSTR,INSTL,I-RAIL,EXTENTION,2 FT - LINEAR P/N: 228232 A - INK: BLACK - MATERIAL: 20 LB. MEAD BOND - SIZE: 17.000” X 11.000” - SCALE: 1-1 - SIDE 1 OF 2
4. REMOVE SPROCKET 5. REMOVE RAIL BOLT 6. IDENTIFY TOP AND BOTTOM EXTENSION RAILS 7. ALIGN REINFORCING STRAPS
8. INSTALL FIRST TWO STRAP BOLTS 9. PLACE BOTTOM EXTENSION RAIL BETWEEN STRAPS 10. ALIGN TOP EXTENSION RAIL BETWEEN STRAPS 11. INSTALL REMAINING TWO STRAP BOLTS
BOTTOM RAIL SECTION
TOP RAIL SECTION
REINFORCING STRAPS (2)
EXTENSION CHAINS (2)
1/4-20 KEPS NUTS (5)
1/4-20 x 13/16" CARRIAGE BOLTS (5)
HOLD SCREWDRIVER IN
TURNBUCKLE SLOT
LOOSEN THE TWO
TURNBUCKLE LOCKING NUTS
NOTE: ONE SIDE OF THE
TURNBUCKLE IS LEFT-HAND
THREAD, THE OTHER SIDE
IS RIGHT-HAND THREAD
UNSCREW AND
REMOVE EACH
END FROM THE
TURNBUCKLE
TOP RAIL SECTION
BOTTOM RAIL SECTION
NOTE: BOTTOM RAIL HAS NOTCH ON CORNER!
REINFORCING STRAP #1
REINFORCING STRAP #2
LINE UP SLOTS ON THE
REINFORCING STRAPS
WITH THE SLOTS ON THE
STOCK I-RAIL
AFTER THE CHAIN IS LOOSENED,
REMOVE THE SPROCKET HOLDER
FROM THE END OF THE RAIL LOOSEN THE NUTS AND
REMOVE THE TWO END
BOLTS ON THE RAIL
NOTE: BE SURE AND KEEP THE
NUTS AND BOLTS, THEY WILL BE
USED AGAIN LATER
FIT THE TOP RAIL SECTION
BETWEEN THE STRAP ON
THIS SIDE AND THE BOTTOM
RAIL SECTION
RAIL EDGES
MUST LINE UP
TOP RAIL SECTION
BE SURE ALL THE
SLOTS ARE ALIGNED
STOCK
I-RAIL
USE 1/4-20 x 13/16" BOLTS
AND KEPS NUTS SUPPLIED
INSTALL THE LAST TWO BOLTS
AND NUTS THROUGH THE
REINFORCING STRAP SLOTS
INSTALL STRAPS ON BOTH
SIDES OF I-RAIL
USE 1/4-20 x 13/16" BOLTS
AND KEPS NUTS SUPPLIED
INSTALL BOLT AND NUT
IN THE SECOND SLOT
INSTALL BOLT AND
NUT IN FIRST SLOT
FIT BOTTOM RAIL SECTION
BETWEEN THE TWO
REINFORCING STRAPS
BE SURE ALL THE
SLOTS ARE ALIGNED
NOTCH ON THE BOTTOM RAIL
WILL BE ON THIS END, BUTTING
UP TO THE NOTCH ON THE STOCK I-RAIL
BOTTOM RAIL SECTION
STOCK I-RAIL
RAIL EDGES MUST LINE UP
FOR SMOOTH TROLLEY
OPERATION