Leviton ACS15-1L - Manual (Page 2)

Step 7 Switch Mounting:
TOP
TOP
LIMITED 5 YEAR WARRANTY AND EXCLUSIONS
Leviton warrants to the original consumer purchaser and not for the benefit of anyone else that this product at the time of its sale by Leviton is free of defects in materials and workmanship under normal and proper use for five years from the purchase date. Leviton’s only obligation is to correct such defects by repair or
replacement, at its option, if within such five year period the product is returned prepaid, with proof of purchase date, and a description of the problem to Leviton Manufacturing Co., Inc., Att: Quality Assurance Department, 59-25 Little Neck Parkway, Little Neck, New York 11362-2591. This warranty excludes and
there is disclaimed liability for labor for removal of this product or reinstallation. This warranty is void if this product is installed improperly or in an improper environment, overloaded, misused, opened, abused, or altered in any manner, or is not used under normal operating conditions or not in accordance with any labels
or instructions. There are no other or implied warranties of any kind, including merchantability and fitness for a particular purpose, but if any implied warranty is required by the applicable jurisdiction, the duration of any such implied warranty, including merchantability and fitness for a particular purpose, is
limited to five years. Leviton is not liable for incidental, indirect, special, or consequential damages, including without limitation, damage to, or loss of use of, any equipment, lost sales or profits or delay or failure to perform this warranty obligation. The remedies provided herein are the exclusive
remedies under this warranty, whether based on contract, tort or otherwise.
DI-000-ACS15-00A-X0
Push Pad (Default settings)
Turn ON from OFF position:
Tap – Lights turn ON.
Turn OFF from ON position:
Tap – Lights turn OFF.
If there is a power outage, the lights will
return to the last state before the power
interruption, when the power is restored.
NOTE: This device has a removable push pad. If there is a need to
re-install the push pad, proceed as follows:
• Line up tabs located on top back of pad with openings in the top
of strap and gently press in.
• Line up tab located on bottom back of pad with opening in the
bottom of strap and gently press in.
• Press bottom of push pad to re-engage.
Cleaning: Clean with a damp cloth. DO NOT use chemical cleaners.
TROUBLESHOOTING
• Lights Flickering
- Lamp has a bad connection.
- Wires not secured firmly under terminal screws of switch
and/or remote.
• Light does not turn ON and Locator LED does not
turn ON
- Circuit breaker or fuse has tripped.
- Lamp is burned out.
- Lamp Neutral connection is not wired.
• Remote does not operate lights
- Ensure that total wire length does not exceed 300 ft.
For additional information, contact the Acenti™
Information Hotline at
1-888-4-ACENTI or visit
Leviton's website at www.leviton.com/acenti
Push
Pad
Locator
Light
OPERATION
NOTE: The locator light will illuminate when the load is in the OFF
position to facilitate access in the dark.
U.S. & Foreign Patents Pending
Copyright © 2004 Leviton Manufacturing Co., Inc.
All Rights Including Trade Dress Rights Reserved
• Restore power at circuit breaker or fuse.
• Lights should turn ON. If lights do not
turn ON, tap push pad.
If lights still do not turn ON, refer to
the TROUBLESHOOTING section.
TOP TO P
Wall Surface
Alignment Hole
(2 places)
Mounting Screw
(2 places)
Alignment Pin
(2 places)
WIRING SWITCH (wall box with Load connection):
Connect wires per WIRING DIAGRAM as follows:
• Green or bare copper wire in wall box to Green terminal screw.
• Load wall box wire identified (tagged) when removing old switch to
terminal screw marked "RD".
• First Traveler Line Hot to terminal screw marked "BL".
• Remove Red insulating label from terminal screw marked "YL/RD".
• Second Traveler wall box wire (note color as above) to terminal
screw marked "YL/RD". This traveler from the switch must
go to the terminal screw on the remote marked "YL/RD".
• Line Neutral wall box wire to remote terminal screw marked "WH".
• Proceed to Step 6.
NOTE: The switch must be installed in a wall box that has a Load
connection. The matching remote must be installed in a wall box
with a Line Hot connection and a Neutral connection. A Neutral wire
to the matching remote needs to be added as shown.
If you are unsure about any part of these instructions, consult a
qualified electrician.
NOTE: Maximum wire length from switch to all installed remotes cannot
exceed 300 ft.
3-Way Wiring with Matching Remote (w/LED)
Application: Step 5c
WIRING MATCHING REMOTE (wall box with Line Hot
connection):
Connect wires per WIRING DIAGRAM as follows:
• Green or bare copper wire in wall box to Green terminal screw.
• Line Hot (common) wall box wire identified (tagged) when removing
old switch and First Traveler to switch terminal screw marked "BL".
• Second Traveler wall box wire from switch to remote terminal
screw marked "YL/RD" (note wire color). This traveler from the
remote must go to the terminal screw on the switch marked "YL/RD".
• Line Neutral wall box wire to remote terminal screw marked "WH".
Hot (Black)
Neutral (White)
Load
Switch Matching Remote (with LED)
YL/RD YL/RD RD
WH BL BL
Black
White
Line
120VAC, 60Hz
Green
Ground
Green
Ground
WH
WIRING SWITCH:
Connect wires per WIRING DIAGRAM as follows:
NOTE: The switch must be installed in a wall box that has a Line Hot connection.
NOTE: Maximum wire length from switch to all installed remotes cannot exceed 300 ft.
•
Green or bare copper wire in wall box to Green terminal screw.
• Line Hot (common) wall box wire identified (tagged) when removing old switch
to terminal screw marked “BL”.
• First Traveler wall box wire to terminal screw marked “RD” (note wire color).
• Remove Red insulating label from terminal screw marked “YL/RD”.
• Second Traveler wall box wire to terminal screw marked “YL/RD”
(note wire color). This traveler from the switch must go to the terminal screw
on the remote marked “YL/RD”.
• Line Neutral wall box wire to terminal screw marked “WH”.
3-Way Wiring with Coordinating Remote
(no LED) Application: Step 5b
Hot (Black)
Neutral (White)
Switch Coordinating Remote (no LED)
YL/RD YL/RD
RD
WH
RD
BL
Black
BL WH
White
Line
120VAC, 60Hz
Green
Ground Green
Ground
Load
(unused)
(unused)
WIRING COORDINATING REMOTE:
Connect wires per WIRING DIAGRAM as follows:
NOTE: "BL" and "RD" terminals on coordinating remote are unused.
Tighten both screws.
NOTE: Maximum wire length from switch to last remote is 300 ft.
•
Green or bare copper wire in wall box to Green terminal screw.
• Load wall box wire identified (tagged) when removing old switch to First
Traveler (note color as above).
• Second Traveler wall box wire (note color as above) to terminal screw
marked "YL/RD". This traveler from the remote must go to the terminal
screw on the switch marked "YL/RD".
• Remove White insulating label from terminal screw marked "WH".
• Line Neutral wall box wire to terminal screw marked "WH".
• Proceed to Step 6.
To complete the Acenti™ Switch and Wallplate installation,
please refer to the instructions included with the Acenti™ Wallplate
and Alignment Plate.
Testing your Switch prior to completely
mounting in wall box:
Step 6
• If Alignment Plate is temporarily positioned using screw as in
Step 4A, remove screw at this point.
• Position all wires to provide room in outlet wall box for device.
• Ensure that the word "TOP" is facing up on the device strap.
• Partially screw in mounting screws in wall box mounting hole.
Mounting Screw
(remove if applicable)
Locator
Light
Additional
Neutral Wire
Terminal
Screw marked
Black (BL)
Terminal
Screw marked
Yellow/Red
(YL/RD)
Matching Remote
4
3
5
BL
YL/RD
WH
1
2
BL WH
YL/RD RD
3
Terminal
Screw marked
Red (RD)
Terminal
Screw marked
White (WH)
Switch
2
1
4
5
BL
YL/RD RD 4
3
1
5
Terminal
Screw marked
Black (BL)
Terminal
Screw marked
Red (RD)
Terminal
Screw marked
White (WH)
Terminal
Screw marked
Yellow/Red
(YL/RD)
Coordinating Remote Switch
BL
YL/RD R D
3
5
WH WH
2 2
1
4