beautypg.com

Life Fitness UT8 User Manual

Page 6

background image

A

SSEMBLING THE

U

PRIGHT

E

XERCISE

B

IKE

Tools Required: Metric Wrench Set, Metric Allen

Wrench Set, Phillips Screwdriver

1. Locate and install the two LEVELER FEET (A) to the bottom of

the REAR STABILIZER (B).

2. With the bends facing rearward, attach the REAR STABILIZER

(B) to the BASE UNIT (C) using two 2-3/8" BUTTON HEAD

SCREWS (1) from the top of the REAR STABILIZER BRACKET

(D) and two 13/16" BUTTON HEAD SCREWS (2) from the front

side of the REAR STABILIZER BRACKET. Tighten the

SCREWS securely.

3. Locate the MONOCOLUMN (E). Cut the WIRE TIE securing the

WIRE (F) to the bottom of the MONOCOLUMN. Slide the

MONOCOLUMN COVER (G) onto the MONOCOLUMN (E) as

shown. Slide the MONOCOLUMN COVER up to the HANDLE-

BAR TUBE (H).

5. Locate and insert the GROMMET (J) into the SIDE ACCESS

HOLE (K) of the MONOCOLUMN (E). Pull the WIRE (F) out

through the SIDE ACCESS HOLE.

6. With the HANDLEBAR TUBE (L) facing the rear of the unit as

shown, slide the MONOCOLUMN (E) into the MONOCOLUMN

BRACKET (M) of the BASE UNIT (C) . Slide the MONOCOL-

UMN down until it is fully seated. Secure the MONOCOLUMN to

the MONOCOLUMN BRACKET using two 3-15/16" HEX HEAD

BOLTS (3) and three THICK FLAT WASHERS (4) (as shown)

from the rear side of the MONOCOLUMN and two 2-3/8" HEX

HEAD BOLTS (5) and THICK FLAT WASHERS (4) from the

user left side of the MONOCOLUMN BRACKET. Tighten the

BOLTS securely.

CAUTION: Be careful not to pinch the WIRE(S) (N) leading

from the MONOCOLUMN BRACKET (M) when inserting the

MONOCOLUMN (E) into the MONOCOLUMN BRACKET.

7. Connect the WIRE(s) (N) leading from the MONOCOLUMN

BRACKET (M) to the corresponding WIRE (F) from the SIDE

ACCESS HOLE (K) of the MONOCOLUMN (E). Slide the

MONOCOLUMN COVER (G) downward to the meet the MAIN

SHROUDS (O). Secure the MONOCOLUMN COVER to the

MAIN SHROUDS using four 1/2" PHILLIPS SCREWS (6) and

matching FLAT WASHERS (7). Tighten the SCREWS securely.

Do not overtighten the SCREWS.

8. Locate the SEAT (P) and SEAT POST (Q). Remove the three

NYLOCK NUTS (8) and FLAT WASHERS (9) from the threaded

studs on the bottom of the SEAT. Align the three threaded studs

of the SEAT with the mounting holes in the SEAT POST

MOUNTING PLATE (R). Secure the SEAT to the SEAT POST

MOUNTING PLATE using the three previously removed

NYLOCK NUTS and FLAT WASHERS. Tighten the NUTS

securely.

9. Locate the SEAT POST CAP (S). With the curved side facing

upward toward the SEAT (P) and the inside notch aligned with

the SEAT POST ADJUSTMENT DECAL, slide the SEAT POST

CAP over the SEAT POST (Q).

10. Locate and slide the SEAT POST SPACER (T) over the end of

the SEAT POST (Q). Using two 1/4" PHILLIPS SCREWS (10),

secure the SEAT POST SPACER to the end of the SEAT POST.

Tighten the SCREWS securely.

11. With the nose of the SEAT (P) facing forward, insert the SEAT

POST (Q) into the SEAT POST SUPPORT (U).

12. Slide the SEAT POST CAP (S) downward to meet the top of the

SEAT POST SUPPORT (U). Secure the SEAT POST CAP to the

SEAT POST SUPPORT using two 1/4" PHILLIPS SCREWS

(11). Tighten the SCREWS securely. Do not overtighten the

SCREWS.

13. Begin inserting the SEAT ADJUSTMENT KNOB (V). Lift upward

on the SEAT (P) and SEAT POST (Q) until the SEAT POST

locks into a position. Tighten the SEAT ADJUSTMENT KNOB

fully. Insert the 1/4" PHILLIPS LOCKING SCREW (12) and tight-

en securely.

14. Locate the ACCESSORY TRAY (W). Position the ACCESSORY

TRAY near the top of the MONOCOLUMN (E) at the DISPLAY

CONSOLE BRACKET (X). While holding the CONNECTOR (Y),

cut the wire tie securing the CONNECTOR to the DISPLAY

CONSOLE BRACKET. Feed the WIRE(s) (Z) leading from the

TOP ACCESS HOLE (AA) of the DISPLAY CONSOLE BRACK-

ET through the center hole of the ACCESSORY TRAY MOUNT-

ING BRACKET (BB). Secure the ACCESSORY TRAY to the

DISPLAY CONSOLE BRACKET using two 5/8" BUTTON HEAD

SCREWS (13) and matching FLAT WASHERS (14). Tighten the

SCREWS securely.

CAUTION: Be careful not to pinch the WIRE(S) (Z) leading

from the DISPLAY CONSOLE BRACKET (X) when securing

the ACCESSORY TRAY (W) to the DISPLAY CONSOLE

BRACKET.

NOTE: Be careful not to let the CONNECTOR (Y) fall into the

DISLAY CONSOLE BRACKET (X).

15. Remove the DISPLAY CONSOLE (CC) from its shipping carton.

Position the DISPLAY CONSOLE above the ACCESSORY

TRAY (W). Connect the WIRE(s) (Z) leading from the DISPLAY

CONSOLE BRACKET (X) to the corresponding JACK(s) located

on the back of the DISPLAY CONSOLE. Secure the DISPLAY

CONSOLE to the DISPLAY CONSOLE BRACKET using four

1/2" PHILLIPS SCREWS (6). Tighten the SCREWS securely. Do

not overtighten the SCREWS.

16. Locate the HANDLEBAR ASSEMBLY (DD). With the handlebars

facing forward, position the HANDLEBAR ASSEMBLY near the

top of the HANDLEBAR TUBE (L). Connect the WIRES (EE)

leading from the HANDLEBAR ASSEMBLY and the HANDLE-

BAR TUBE. Slide the HANDLEBAR ASSEMBLY fully into the

HANDLEBAR TUBE. Secure the HANDLEBAR ASSEMBLY to

the HANDLEBAR TUBE using four 5/8" BUTTON HEAD

SCREWS (15) and matching FLAT WASHERS (16). Tighten the

SCREWS securely.

CAUTION: Be careful not the pinch the WIRES (EE) when

sliding the HANDLEBAR ASSEMBLY (DD) into the HAN-

DLEBAR TUBE (L).

17. Locate the RIGHT PEDAL (FF) (marked with an "R") and

PEDAL STRAP (GG) (marked with an "R"). With the side of the

PEDAL STRAP marked with an “R” facing upward, slide the slot-

ted end of the PEDAL STRAP through the left slot in the

PEDAL. Fasten one of the slots onto the TAB located under the

left slot of the PEDAL. Bend the PEDAL STRAP upward and

slide the remaining end of the PEDAL STRAP through the right

slot in the PEDAL and into the STRAP ADJUSTMENT CLIP. The

PEDAL STRAP should securely engage the STRAP ADJUST-

MENT CLIP.

18. Install the RIGHT PEDAL (FF) to the USER RIGHT CRANK

ARM (HH). Repeat for the LEFT PEDAL (JJ) (marked with an

"L") and PEDAL STRAP (KK) (marked with an "L").
NOTE: The LEFT PEDAL (JJ) has reverse threads.

19. Position the unit in the desired location for use. The unit can be

easily moved into place by lifting the rear of the unit and rolling it

on the front rollers. Level the unit before use. Refer to the level-
ing instructions stated in the operations portion of this manual.

5