LG DR787T - Manual

Lock (Parental Control) Settings Lock (Parental Control) Settings
Notes:
• Lock System and TV Rating options are effective for digi-
tal TV program only.
• When you set the TV Rating, a program with a TV Rating
beyond your rating setting cannot be recorded correctly.
(Normal recording, Timer recording, etc.)
• The default TV Rating setting is to allow all programs to
be viewed.
Lock System
You can lock certain unsuitable channels to prevent chil-
dren from accessing them, or set a TV Rating, so that any
digital TV program classified above that rating by the broad-
caster will be restricted. If the [Lock System] is set to [OFF],
TV Rating options are not effective.
The Lock System option is effective for TV Rating and
Downloadable Rating options.
1. Select [Lock System] option then press B.
2. To access the Lock Menu options, you must input the 4-
digit password you created.
If you have not yet entered a password you are prompt-
ed to do so. Input a 4-digit password. Enter it again to
verify. If you make a mistake, press CLEAR.
3. Select [ON] or [OFF] using the v / V buttons.
4. Press ENTER to confirm your setting.
Rating
Blocks playback of rated DVDs based on their
content. Not all discs are rated.
1. Select [Rating] option then press B.
2. Follow step 2 as shown in [Lock System] above.
3. Select a rating from 1 to 8 using the v / V buttons.
[1]-[8]: Rating one (1) has the most restrictions and rat-
ing eight (8) is the least restrictive.
[No Limit]: If you select [No Limit], parental
control is not active and the disc plays in full.
4. Press ENTER to confirm your rating selection, then
press HOME to exit the menu.
Note:
If you set a rating for the DVD Player/Recorder, all disc scenes
with the same rating or lower will be played. Higher rated
scenes will not be played unless an alternate scene is available
on the disc. The alternative must have the same rating or a
lower one. If no suitable alternative is found, playback will stop.
You must enter the 4-digit password or change the rating level
in order to play the disc.
Set Password
You can enter or change password.
1. Select [Set Password] option then press B.
2. Follow step 2 as shown in [Lock System] above.
To change the password, press ENTER when the
[Change] option is highlighted, then input old password.
Input new password. Enter it again to verify.
To delete the password, select [Delete] option then
press ENTER, then input old password. The password
is deleted.
3. Press HOME to exit the menu.
If you forget your password
If you forget your password you can reset it using the fol-
lowing steps:
1. Press HOME and the Home menu appears.
2. Select [Setup] > [Start] and press ENTER.
3. Input the 6-digit number [210499]. When the message
appears, select [OK] then press ENTER. The password
will be reset.
4. Enter a new password as described above.
Note:
If you delete your password, all ratings will be reset to the
default setting. The default setting is to allow all programs to be
viewed in full.
Area Code
Enter the Area Code whose standards were used to rate
the DVD video disc, based on the Area Code List in the
owner’s manual.
1. Select [Area Code] option then press B.
2. Follow step 2 as shown in [Lock System] above.
3. Select the first character using v / V buttons.
4. Shift the cursor using B buttons and select the second
character using v / V buttons.
5. Press ENTER to confirm your area code
selection, then press HOME to exit the menu.
Model: RC797T
DR787T
Correction Sheets
The descriptions for the “Lock (Parental Control) Settings”on the owner’s manual
(pages 23-24) are changed as follows due to software upgrade.
P/NO: 3840R-L011G
RC200_D-RRT Sheet 10/17/07 10:34 AM Page 1