Kenwood FleetSync TK-980 - Manual (Page 2)

ADS#44307 Printed in USA
JQA-QMA1205
■ KMC-9C
Control Station
Desktop Microphone
■ KMC-27A
Microphone
(MIL-SPEC Noise-Canceling)
■ KMC-27B
Microphone
■ KMC-28A
Keypad Microphone
(MIL-SPEC Noise-Canceling)
■ KCT-18
Ignition Sense Cable
■ KCT-19
Accessories Connector
Cable
■ KCT-31
PC Serial Interface
Cable
■ KES-3
External Speaker
■ KES-5
External Speaker
■ KMB-2B
Mounting Case
■ KMB-10
Key Lock Adapter
■ KMB-20
Mounting Case
■ KPS-15
DC Power Supply
■ KLF-2
Line Noise Filter
■ KAP-1
PA/HA Unit
■ KDS-100
Mobile Data Terminal
■ KGP-2A/2B
GPS Receiver /
Modem Unit
All accessories and options may not be available in all markets.
Contact an authorized Kenwood dealer for details and complete list of all accessories and options.
Options
Specifications
footnotes from Front:
1 Trunked Format: 32 Systems max. (prog. for LTR ® or Conventional),
250 Groups per system max (limited per repeater channels
programmed).
2 DTMF Encode includes PTT ID, Emergency ANI, Manual Encode
(KMC-28A DTMF mic required), Auto-Dial (32 numbers); DTMF
Decode includes Stun (dead beat disable), primary/secondary
selective call with call alert and transpond.
3 Ignition sense requires KCT-34 ACC cable & KCT-18 Ignition
sense cable options.
4 Public Address / Horn Alert Option- requires KAP-1 PA/HA Unit and
KCT-34 ACC Cable options.
5 KPG-49D required: Windows ® 98/ NT/ 2000/ Me/XP compatible.
6 Kenwood LTR ® Features: KPG-49D Group Delete/Add, LTR ® Talk
Around, Scan Revert Group Display, System Scan, Group Scan,
Auto Search.
7 FleetSync ® (not FleetSync ® II capable)
8 Short Text Messages are radio stored & LCD displayed.
Model TK-980 TK-981
GENERAL
Frequency Range
Type 1 (RX)
851~870 MHz 935 ~ 941 MHz
Type 2 (TX) 806 ~ 825 MHz, 896 ~ 902 MHz,
Type 3 (Talk Around) 851 ~ 870 MHz 935 ~ 941 MHz
Systems Max. 32
Group Max. 250 per system
Channels
LTR
® Mode Max. 600
(Conventional) Max. 250
PLL Channel Spacing 25 kHz 12.5 kHz
(PLL step: 12.5 kHz)
Operating Voltage 13.6 V DC ± 15 %
Current Drain
Standby Less than 0.4 A
Receive Less than 1.0 A
Transmit Less than 7.0 A
Duty Cycle Transmit: 20%
Operating Temperature -22° F ~ +140° F
Range (-30° C ~ +60° C)
Frequency Stability ±0.00015%
(-22° F ~ +140° F)
Antenna Impedance 50 Ω
Dimensions (W x H x D) 5-1/2 x 1-1/2 x 5-3/4 in. (140 x 40 x 145 mm)
Weight (net) 2.07 lbs. (940 g)
FCC ID ALH24563110 ALH24572110
IC Certification 282195546A 282195545A
Model TK-980 TK-981
RECEIVER (Measurements made per TIA/EIA-603)
Sensitivity (12 dB SINAD) 0.25 µV
Selectivity* 75 dB 68 dB
Intermodulation Distortion 70 dB 65 dB
Spurious Response* 80 dB
Audio Output 4 W with less than 5% distortion
Channel frequency spread 19 MHz 6 MHz
TRANSMITTER (Measurements made per TIA/EIA-603)
RF Power Output 15 W
Spurious & Harmonics 60 dB
Modulation 16KØF3E 11KØF3E
FM Noise 45 dB 40 dB
Audio Distortion Less than 3% Less than 5%
Microphone Impedance Low Impedance
Channel Frequency Spread 64 MHz 45 MHz
FleetSync ® is a registered trademark of Kenwood Corporation.
LTR ® is a registered trademark of Transcrypt International.
* Typical specifications
Kenwood follows a policy of continuous advancement in development.
For this reason specifications may be changed without notice.
GPS-2A
GPS-2B
Applicable MIL-STD
Standard MIL 810C MIL 810D MIL 810E MIL 810F
Methods/Procedures Methods/Procedures Methods/Procedures Methods/Procedures
Low Pressure 500.1/Procedure I 500.2/Procedure I, II 500.3/Procedure I, II 500.4/Procedure I, II
High Temperature 501.1/Procedure I, II 501.2/Procedure I, II 501.3/Procedure I, II 501.4/Procedure I, II
Low Temperature 502.1/Procedure I 502.2/Procedure I, II 502.3/Procedure I, II 502.4/Procedure I, II
Temperature Shock 503.1/Procedure I 503.2/Procedure I 503.3/Procedure I 503.4/Procedure I, II
Solar Radiation 505.1/Procedure I 505.2/Procedure I 505.3/Procedure I 505.4/Procedure I
Humidity 507.1/Procedure I, II 507.2/Procedure II, III 507.3/Procedure II, III 507.4
Sand & Dust 510.1/Procedure I 510.2/Procedure I 510.3/Procedure I 510.4/Procedure I, III
Vibration 514.2/Procedure VIII, X 514.3/Procedure I 514.4/Procedure I 514.5/Procedure I
Shock 516.2/Procedure I, II, III, V 516.3/Procedure I, IV, V 516.4/Procedure I, IV, V 516.5/Procedure I, IV, V