Kenwood TK-7160H - Manual (Page 2)

ADS#44107 Printed in USA
JQA-QMA1205
■ KMC-35
Microphone
(supplied microphone)
■ KMC-36
Keypad Microphone
■ KMC-9C
Control Station
Desktop Microphone
■ KCT-18
Ignition Sense Cable
(requires KCT-39 option)
■ KCT-36
3m Extension Cable
(for KCT-39)
■ KCT-39
Connection Cable
■ KAP-2
Horn Alert/Public
Address Relay Unit
■ KES-3
External Speaker
■ KES-5
External Speaker
(requires KAP-2)
■ KMB-10
Key Lock Adapter
■ KLF-2
Line Noise Filter
■ KPS-10A
DC Power Supply
■ KPS-15
DC Power Supply
■ KDS-100
Mobile Data Terminal
(requires KCT-39 option)
■ KGP-2A/2B
GPS Receiver /
Modem Unit
(requires KCT-39 option)
Options
All accessories and options may not be available in all markets. Contact an authorized
Kenwood dealer for details and complete list of all accessories and options.
Specifications
Applicable MIL-STD
Model TK-7160 TK-7160H TK-8160 TK-8160H
GENERAL
Frequency Range
136~174 MHz 450~490 MHz
Number of Channels
Zone Max.128 per Radio
Channel Max.128 per Zone
Channel Spacing
Wide 25 kHz, 30 kHz 25 kHz
Narrow 12.5 kHz, 15 kHz 12.5 kHz
Operating Voltage 13.6 V DC±15 %
Current Drain
Standby 0.4 A 0.4 A 0.4 A 0.4 A
Receive 1.0 A 1.0 A 1.0 A 1.0 A
Transmit 8.0 A 14.0 A 8.0 A 14.0 A
Duty Cycle Transmit: 20 %
Operating Temperature Range -22 ºF ~ +140 ºF (-30 ºC ~ +60 ºC)
Frequency Stability ±0.00025 % (-22 ºF ~ +140 ºF)
Antenna Impedance 50 Ω
Channel Frequency Spread 38 MHz 40 MHz
Dimensions (W x H x D), 6-5/16” x 1-11/16” x 5-3/8”
Projections not included (160 mm x 43 mm x 137 mm)
Weight (net) 2.6 lbs. (1.18 kg)
FCC ID K4437663110 K4437663210 K4437673110 K4437673210
IC Certification — 282F-37663210 — 282F-37673210
Model TK-7160 TK-7160H TK-8160 TK-8160H
RECEIVER (Measurements made per EIA/TIA-603)
Sensitivity (12dB SINAD)
Wide 0.28 µV
Narrow 0.35 µV
Selectivity
Wide 75 dB
Narrow 65 dB
Intermodulation Distortion
Wide 70 dB
Narrow 60 dB
Spurious Response 75 dB
Audio Output
(4
Ω Impedance) 4 W with less than 5 % distortion
TRANSMITTER (Measurements made per EIA/TIA-603)
RF Output Power
5 W / 25 W 25 W / 50 W 5 W / 25 W 25 W / 45 W
Spurious Response 70 dB
Type of Emission
Wide 16K0F3E
Narrow 11K0F3E
FM Hum & Noise
Wide 45 dB
Narrow 40 dB
Microphone Impedance 600 Ω
Audio Distortion
Wide 3 %
Narrow 5 %
Standard MIL 810C MIL 810D MIL 810E MIL 810F
Methods/Procedures Methods/Procedures Methods/Procedures Methods/Procedures
Low Pressure 500.1/Procedure I 500.2/Procedure I, II 500.3/Procedure I, II 500.4/Procedure I, II
High Temperature 501.1/Procedure I, II 501.2/Procedure I, II 501.3/Procedure I, II 501.4/Procedure I, II
Low Temperature 502.1/Procedure I 502.2/Procedure I, II 502.3/Procedure I, II 502.4/Procedure I, II
Temperature Shock 503.1/Procedure I 503.2/Procedure I 503.3/Procedure I 503.4/Procedure I, II
Solar Radiation 505.1/Procedure I 505.2/Procedure I 505.3/Procedure I 505.4/Procedure I
Rain* 506.1/Procedure II 506.2/Procedure II 506.3/Procedure II 506.4/Procedure III
Humidity 507.1/Procedure I, II 507.2/Procedure II, III 507.3/Procedure II, III 507.4
Salt Fog 509.1/Procedure I 509.2/Procedure I 509.3/Procedure I 509.4
Dust 510.1/Procedure I 510.2/Procedure I 510.3/Procedure I 510.4/Procedure I, III
Vibration 514.2/Procedure VIII, X 514.3/Procedure I 514.4/Procedure I 514.5/Procedure I
Shock 516.2/Procedure I, II, III, V 516.3/Procedure I, IV, V 516.4/Procedure I, IV, V 516.5/Procedure I, IV, V
* MILSTD-810 506.X Procedure II “rain drip” specifications are conditional on installed KMC-35/36 microphones and supplied accessory connector covers.
Kenwood follows a policy of continuous advancement in development.
For this reason specifications may be changed without notice.
* FleetSync ® is not compatible with FleetSync ® II offered in some Kenwood products.
** The 20-pin 160-Series Easy Option Port is a not compatible with the Kenwood 26-pin Easy Option Port connector/options.
The traditional PCB connections are available for wired-in boards not having a 20-pin Easy Option Port connector.
FleetSync ® is a registered trademark of Kenwood Corporation.
Windows ® is a registered trademark of Microsoft Corporation in the United States and other countries.
All other trademarks are property of their respective owners.
footnotes from front:
1 DTMF includes PTT ID, Emergency ANI, Manual Encode
(KMC-36), Auto-Dial (9 numbers) & Stun.
2 Special Alert Tone Patterns operate for 2-Tone, DTMF, FleetSync ®
selective call decode.
3 Call Key 1 & 2: operates for 2-Tone, DTMF and FleetSync ®
status encode.
4 KCT-39 required for 4 CH remote control, ignition sense (KCT-18),
KGP-2A/B, KDS-100, data modems, external GPS interface.
5 KCT-39 & KCT-18 ignition sense cable options required.
6 KAP-2 required: Horn Alert operates for FleetSync ® , 2-Tone or
DTMF selective call decode.
7 KPG-99D program software required: Windows ® 98/ NT/2000/ Me/XP
compatible; English/Spanish program screen languages.
8 FleetSync ® GPS features require a KCT-39 and an external GPS
receiver with NMEA TTL level serial data output; set Port 1 & 2
(Inputs) to “GPS NMEA.”
GPS-2A
GPS-2B