Kawasaki 843327 - Manual (Page 11)

A AC CC CE ES SS SO OR RIIE ES S
U Usse e o on nllyy a acccce esssso orriie ess tth ha att a arre e rre ecco om mm me en nd de ed d b byy tth he e m ma an nu uffa accttu urre err ffo orr yyo ou urr m mo od de ell..
Accessories that may be suitable for one tool may become hazardous when used on
another tool.
A Allw wa ayyss a atttta acch h g grro ou un nd de ed d ((3 3--p prro on ng g)) e exxtte en nssiio on n cco orrd dss tto o g grro ou un nd de ed d ((3 3--h ho olle e)) o ou uttlle ettss..
IIff yyo ou u m mu usstt u usse e a an n e exxtte en nssiio on n cco orrd d,, b be e ssu urre e tth ha att tth he e g ga au ug ge e iiss lla arrg ge e e en no ou ug gh h tto o cca arrrryy
tth he e a am mo ou un ntt o off ccu urrrre en ntt n ne ecce essssa arryy ffo orr yyo ou urr p po ow we err tto oo oll.. If not, your tool may experi-
ence a loss of power, excessive voltage drop or overheating. The smaller the gauge
number, the heavier the cord (see table on below).
R RE EC CO OM MM ME EN ND DE ED D S SIIZ ZE ES S O OF F E EX XT TE EN NS SIIO ON N C CO OR RD DS S 1 12 20 0 V VO OL LT T A AC C 6 60 0 H HZ Z T TO OO OL LS S
T TO OO OL L C CU UR RR RE EN NT T R RA AT TIIN NG G C CO ON ND DU UC CT TO OR R S SIIZ ZE E IIN N A A..W W..G G
AMPERE 10FT. 25FT. 50FT. 100FT.
3-6 18 18 18 18
6-8 18 18 18 16
8-10 18 18 18 14
10-12 16 16 14 14
12-16 14 12 12 -
16-20 12 12 12 -
S SP PE EC CIIF FIIC CA AT TIIO ON NS S
S SP PE EC CIIF FIIC CA AT TIIO ON NS S
Input 120V 60Hz 13 Amp
No-Load Speed 5000 RPM
Blade Diameter 7-1/4”
Max. Depth of Cut 2-1/2” @ 90°
1-5/8” @ 45°
• Mark out the line to be cut so it
is easily visible.
• Start inside the area to be cut out.
• Set the shoe against the work
piece at an angle.
• Lift the blade guard.
• Pull the trigger to start the saw.
• When the blade reaches full
speed, slowly feed the blade into
the work piece. When the blade
starts cutting, release the blade
guard.
M MA AIIN NT TE EN NA AN NC CE E A AN ND D C CL LE EA AN NIIN NG G
T Th hiiss C Ciirrccu ulla arr S Sa aw w iiss llu ub brriicca atte ed d b be effo orre e iitt lle ea avve ess
tth he e ffa acctto orryy.. This lubrication should last for the life of the tool. No further
lubrication is required.
U Usse e o on nllyy m miilld d sso oa ap p a an nd d a a d da am mp p ccllo otth h tto o cclle ea an n tth he e tto oo oll.. Never let any liquid get
inside the casing. Never immerse any part of the tool in a liquid. Always keep the
ventilation openings clear.
R Re eg gu ulla arrllyy cclle ea an n tth he e vve en nttiilla attiio on n ssllo ottss iin n yyo ou urr tto oo oll a an nd d cch ha arrg ge err u ussiin ng g o on nllyy a a sso offtt
b brru ussh h o orr d drryy ccllo otth h..
IIn nssp pe ecctt a allll m mo ou un nttiin ng g ssccrre ew wss rre eg gu ulla arrllyy.. T Tiig gh htte en n a an nyy llo oo osse e ssccrre ew wss.. F Fa aiillu urre e tto o kke ee ep p
tth he e m mo ou un nttiin ng g ssccrre ew wss ttiig gh htt cco ou ulld d rre essu ulltt iin n sse erriio ou uss iin njju urriie ess..
Never open the Circular Saw case. Do not attempt to repair the Circular Saw your-
self. Opening the tool will void your warranty.
L LA AS SE ER R M MA AIIN NT TE EN NA AN NC CE E
For best performance, perform the following maintenance regularly:
D Diisscco on nn ne ecctt m ma acch hiin ne e ffrro om m p po ow we err sso ou urrcce e.. Carefully clean
sawdust from laser lens with a cotton swab. Do not use solvents of any kind
since they may damage the lens.
19