Kawasaki 840272 - Manual (Page 8)

U US SIIN NG G T TH HE E A AN NG GL LE E G GR RIIN ND DE ER R::
FFo orr b beesstt tto oo oll cco on nttrro oll,, m maatteerriiaall rreem mo ovvaall aan nd d m miin niim maall
llo oaad diin ng g,, kkeeeep p tth hee aan ng gllee b beettw weeeen n tth hee d diisscc aan nd d tth hee w wo orrkk ssu urrffaaccee aatt aap pp prro oxxii--
m maatteellyy 3 30 0°° w wh heen n g grriin nd diin ng g aan nd d 1 10 0°°--1 15 5°° w wh heen n ssaan nd diin ng g..
• Do not cover exhaust vents when the Angle Grinder is in use. This may cause
damage to the motor and reduce efficiency.
• Guide back and forth over the work piece in a steady motion.
• When cutting avoid tilting the Angle Grinder in the cutting plane. Ensure the cut-
ting wheel has a clean cutting edge.
• To cut hard stone a diamond cutting wheel is recommended.
• Do nut use cutting wheel for rough grinding.
M MA AIIN NT TE EN NA AN NC CE E A AN ND D C CL LE EA AN NIIN NG G
A Allw waayyss U UN NP PL LU UG G tth hee tto oo oll ffrro om m tth hee p po ow weerr sso ou urrccee b beeffo orree
cclleeaan niin ng g o orr m maaiin ntteen naan nccee..
• The armature and motor are the heart of the power tool. Exercise care to ensure
they do not become damaged or effected by oil or water.
• Inspect the carbon brushes regularly and replace them when they are worn.
(about 1/3 of the way up)
• Regularly inspect all mountings and screws and ensure they are properly tight-
ened. Failure to do so may result in serious damage.
• Consult an authorized maintenance service agent in event of damage.
• Clean and dust the Angle Grinder after each use.
• Use compressed air to blow out any accumulated dust or grit. Tiny
particles from metal grinding often accumulate inside your tool and could
create an electrical shock hazard.
• Never use solvents or harsh chemicals. Use only mild soap and a damp cloth to
clean the tool. Never let any liquid get inside the casing. Never immerse any
part of the tool in a liquid. Always keep the ventilation openings clear.
• Regularly clean the ventilation slots in your tool using a soft brush or dry cloth.
14
O OP PE ER RA AT TIIN NG G T TH HE E O ON N//O OFFFF S SW WIIT TC CH H
N Neevveerr ssw wiittcch h tth hee A An ng gllee G Grriin nd deerr ““O ON N”” o orr ““O OFFFF”” w wh hiillee
u un nd deerr llo oaad d cco on nd diittiio on nss..
A Allw waayyss aallllo ow w tth hee A An ng gllee G Grriin nd deerr tto o cco om mee u up p tto o ffu ullll ssp peeeed d b beeffo orree tto ou ucch hiin ng g aan nyy
ssu urrffaaccee..
A Allw waayyss ttaakkee tth hee tto oo oll aaw waayy ffrro om m tth hee w wo orrkkp piieeccee b beeffo orree ttu urrn niin ng g tth hee tto oo oll ““O OFFFF””..
Let the tool come to a complete stop before setting it down.
T Th hiiss tto oo oll o op peerraatteess b beesstt u un nd deerr lliig gh htt p prreessssu urree.. Exerting heavy pressure will not
speed up the work and may cause damage to the motor.
• When starting hold the Angle Grinder firmly with both hands. One hand on the
rear handle or the motor housing and the other hand on the side handle.
• To turn the Angle Grinder ““O ON N”” without locking it, apply forward pressure to
the rear of the ON/OFF switch. When pressure is released, the switch snaps to the
““O
OFFFF”” position.
• The switch can be locked in the ““O ON N”” position, a convenience for long grinding
operations. To lock the switch ““O ON N””, firmly press froward the rear of the
switch and then press down the front to lock the tab inside the notch on the
body of the grinder.
• To unlock the switch, simply press the rear of the switch. The switch is spring
loaded and will snap back automatically.
13
ON/OFF
SWITCH