Kawasaki 840517 - Manual (Page 7)

R RE EM MO OV VIIN NG G//A AT TT TA AC CH HIIN NG G B BA AT TT TE ER RY Y P PA AC CK K
R RE EM MO OV VE E B BA AT TT TE ER RY Y P PA AC CK K::
1. Press both release buttons on either side of
the Cordless Drill to release the battery pack.
2. Pull battery pack free of Cordless Drill.
A AT TT TA AC CH H B BA AT TT TE ER RY Y P PA AC CK K::
1. Align the raised portion of the battery pack
with the groove in the battery compartment
of the Cordless Drill.
2. Press the battery pack into place. Make sure
the latches are securely fastened. Do not use
the Cordless Drill if the battery pack is not
seated properly.
C CH HA AR RG GE ER R
B Beeffo orree u ussiin ng g b baatttteerryy cch haarrg geerr,, p plleeaassee rreeaad d ccaarreeffu ullllyy aallll
iin nssttrru uccttiio on nss aan nd d ccaau uttiio on naarryy m maarrkkiin ng gss o on n b baatttteerryy cch haarrg geerr,, b baatttteerryy p paacckk aan nd d
p prro od du ucctt u ussiin ng g b baatttteerryy..
T Th hee cch haarrg geerr w wiillll n no ott aau utto om maattiiccaallllyy ttu urrn n ““O OFFFF”” w wh heen n tth hee
b baatttteerryy p paacckk iiss ffu ullllyy cch haarrg geed d.. The charging indicator light will remain ““O ON N””
until the charger is disconnected from the electrical outlet.
U Ussee o on nllyy tth hee cch haarrg geerr w wh hiicch h aacccco om mp paan niieed d yyo ou urr p prro od du ucctt o orr d diirreecctt rreep pllaacceem meen ntt aass
lliisstteed d iin n tth hiiss m maan nu uaall.. Do not substitute any other charger. Use only Alltrade
approved chargers with your product.
D Do o n no ott d diissaasssseem mb bllee cch haarrg geerr..
D Do o n no ott u ussee cch haarrg geerr iiff iitt h haass b beeeen n d daam maag geed d,, lleefftt o ou uttd do oo orrss iin n tth hee rraaiin n,, ssn no ow w,, w weett
o orr d daam mp p een nvviirro on nm meen nttss,, o orr iim mm meerrsseed d iin n lliiq qu uiid d..
T Th hee b baatttteerryy p paacckk aan nd d cch haarrg geerr h heeaatt d du urriin ng g cch haarrg giin ng g.. Place the charger on a flat,
non-flammable surface away from flammable materials with at least four inches of
clearance to allow proper air circulation around the charger and battery pack.
W Wh heen n tth hee b baatttteerryy p paacckk rreeq qu uiirreess rreecch haarrg giin ng g,, aa 3 3--5 5 h ho ou urr cch haarrg gee aallllo ow wss tth hee tto oo oll tto o
o op peerraattee aatt ffu ullll p po ow weerr.. A charging indicator light on the charger will illuminate to
show that charging is taking place.
C CH HA AR RG GIIN NG G B BA AT TT TE ER RY Y P PA AC CK K
C CH HA AR RG GE E B BA AT TT TE ER RY Y P PA AC CK K::
1. Make sure the trigger
on the Cordless Drill
is in the ““O
OFFFF”” position
and remove the battery
pack from the Cordless
Drill.
2. Plug 120V AC Adapter
into household outlet
and into side of battery
charger. Insert battery
pack into battery charger.
When the battery is
placed in the charger, the
red LED indicator light
will remain on.
3. When fully charged, reattach battery pack onto Cordless Drill,
making certain latches fasten securely. Cordless Drill will not
operate properly if the battery pack is not seated properly.
A AS SS SE EM MB BL LY Y
B Bee aaw waarree tth haatt tth hiiss tto oo oll iiss aallw waayyss iin n aan n o op peerraattiin ng g cco on nd diittiio on n
b beeccaau ussee iitt d do oeess n no ott h haavvee tto o b bee p pllu ug gg geed d iin ntto o aan n eelleeccttrriiccaall o ou uttlleett.. Always turn
the switch ““O OFFFF”” and remove the battery pack before changing bits.
12 11
RELEASE
BUTTON
BATTERY
CHARGER
BATTERY PACK
120V AC
ADAPTER
LED LIGHT