beautypg.com

Mobile station base station, Kgp-2b, Kgp-2a – Kenwood KGP-2A User Manual

Page 2: Mil-std environmental standards, Compact lightweight design, Led status indicators, Dsp modem, Multi-purpose programmable i/o’s, Control

background image

Options

ADS#44507 Printed in USA

KCT-34

Interface Cable
(for TK-780/880
980/981 mobiles)

KCT-40

Interface Cable
(for TK-7180/8180
7150/8150 mobiles)

KGP-2B

GPS CONTROLLER-MODEM

Main Data TX Commands

◗ Single Call ◗ Multiple Call ◗ Group Call ◗ Auto Data TX
Request

◗ District Call ◗ Emergency ◗ Input Data Request

(I/IO input ports; contact closures, sensors, etc.)

Main Mobile Station Settings

◗ Outputs Data Request (I/O ports outputs) ◗ GPS Data

Mobile Station

Base Station

KCT-35

Interface Cable
(for 60G/62G-Series mobiles)

*1

KCT-36

Extension Cable
(for KCT-34/35/40)

*1

160G/62G-Series Mobiles: TK-760G/762G/860G/862G/768G/868G/863G except for European models

Not all accessories may be available, please contact dealers for details.

Applicable MIL-STD

Military Standard

Method / Procedure

Method / Procedure Method / Procedure

810C

810D

810E

Dust

510.1/Proc. 1

510.2/Proc. 1

510.3/Proc. 1

Vibration

514.2/Proc. 8,10

514.3/Proc. 1 Cat.8

514.4/Proc. 1 Cat.8

Shock

516.2/Proc. 1,2,5

516.3/Proc. 1,4

516.4/Proc. 1,4

Specifications

General Specification
Dimensions (W x H x D) without projections

5.51 x 1.81 x 3.94 in (140 x 46 x 100mm)

Weight: KGP-2A

1.01 lbs (460 g)

KGP-2B

0.93 lbs (420 g)

Standard Input Voltage

DC 13.6V negative ground

(Input Voltage Range)

(DC 10.0V to 15.7V)

Temperature Range

-22°F to + 140°F (-30°C to + 60°C)

Current Drain

< 300 mA (KGP-2A) , < 240 mA (KGP-2B)

GPS Receiver Unit (applies to KGP-2A only)
Receiver Type

Parallel 9 channels

Receiver Frequency

1,575.42 MHz

Supply Voltage to Antenna

DC 3.3V ± 0.2 V

GPS Backup Term

More than 2 month (fully charged)

Modem
Modulation

Minimum shift keying (MSK)

Modulation Rate

1,200 / 2,400 bps

Modem Encode Level Range

100 ~ 1,000 mVrms

Modem Decode Level Range

100 ~ 1,000 mVrms

Input Impedance

600 Ω

Output Impedance

600 Ω

JQA-QMA1205

MIL-STD Environmental Standards

Compliance with MIL-STD 810 C/D/E environmental
standards for resistance to dust, vibration and shock
ensures stable performance even in demanding conditions.

KGP-2A

GPS RECEIVER-MODEM

Compact Lightweight Design

Measuring just 5.51 x 1.81 x 3.94 inches
(W x H x D) and weighing 1.01 pounds, the
KGP-2A can be easily installed in any vehicle.

Flash Memory

Flash memory permits uploading KGP-2A/2B
unit firmware upgrades with a computer.

LED Status Indicators

LEDs provide a quick troubleshooting indica-
tor to confirm DC power, data communica-
tions with the connected mobile radio or if
a GPS signal is being received.

Compact Lightweight Design

Measuring just 5.51 x 1.81 x 3.94 inches
(W x H x D) and weighing 0.93 pounds,
the KGP-2B can be easily installed out of
the way base installation.

DSP Modem

The receiver features a modern DSP-type
modem (Digital Signal Processor) capable
of 1200/2400 bps data communications.

DSP Modem

The receiver features a modern DSP-type
modem (Digital Signal Processor) capable
of 1200/2400 bps data communications.

Kenwood follows the policy of continuous advancement in development.

For this reason specifications may be changed without notice.

MIL-STD Environmental Standards

Compliance with MIL-STD 810 C/D/E environmental stan-
dards for resistance to dust, vibration and shock ensures
stable performance even in demanding conditions.

rear panel

rear panel

Multi-purpose

Programmable I/O’s

Each KGP-2A has sixteen programmable
I/O’s for either an analog “input” or output”
[available at external connectors ACC2
(DB-9) & ACC-3 (DB-15)]. The inputs are
useful for vehicular sensors, switches,
contacts, etc. and generate a report to the
KGP-2B base unit each time the status
changes*. The outputs can be used to trigger
external relays and controls*. A KGP-2B base
unit can be commanded by a control/base
station computer running a KGP-2A/2B AVL
dispatcher application to activate/deactivate
KGP-2A fleet unit outputs and/or poll current
input/output status.

* Requires additional circuitry and added parts; also requires

a KGP-2A/B compatible AVL/dispatch software

capable of utilizing these I/O’s.

Flash Memory

Flash memory permits uploading KGP-2A/2B
unit firmware upgrades with a computer.

Control

The KGP-2A/2B air protocol commands permit
a KGP-2B base unit to request any KGP-2A
fleet unit to send any currently stored data or
mobile station settings. AVL mapping / dispatch
CAD software developers are provided with
these commands and all protocol information
to utilize in their products.

LED Status Indicators

LEDs provide a quick troubleshooting
indicator to confirm DC power, data commu-
nications with the connected mobile radio.

This manual is related to the following products: