Kawasaki 840271 - Manual (Page 5)

FFU UN NC CT TIIO ON NA AL L D DE ES SC CR RIIP PT TIIO ON N
C CO ON NT TR RO OL LS S A AN ND D C CO OM MP PO ON NE EN NT TS S::
1. 1/2" Variable Speed Hammer-Drill
2. 13mm (1/2") Chuck
3. Speed Control Adjusting Switch
4. On/Off Switch
5. Lock-On Switch
6. Forward/ Reversing Switch Lever
7. Adjustable Side Handle
8. Hammer / Drill Selector
9. Depth Gauge
A AS SS SE EM MB BL LY Y
D Diisscco on nn neecctt tth hee p po ow weerr p pllu ug g ffrro om m tth hee A AC C p po ow weerr sso ou urrccee
b beeffo orree aan nyy aasssseem mb bllyy,, aad djju ussttm meen nttss,, o orr aad dd diin ng g//rreem mo ovviin ng g aacccceesssso orriieess..
Following this preventative step reduces the risk of the drill coming on acciden-
tally and the risk of damage to the workpiece and injury to the operator.
8
IIff tth hee b biitt b beecco om meess b bo ou un nd d iin n tth hee w wo orrkk p piieeccee,, rreelleeaassee tth hee ttrriig gg geerr iim mm meed diiaatteellyy
aan nd d p prreep paarree ffo orr tth hee tto oo oll tto o kkiicckkb baacckk tto ow waarrd d yyo ou u.. Reverse the direction of rota-
tion, then back out the bit by slowly squeezing the trigger.
M Maakkee ssu urree aallll aacccceesssso orriieess aarree rraatteed d ffo orr tth hee rreecco om mm meen nd deed d ssp peeeed d o off tth hee d drriillll..
Brushes, grinding wheels and other accessories may fall apart if run at too high
a speed, sending dangerous debris flying at the operator.
N Neevveerr w weeaarr g gllo ovveess w wh heen n o op peerraattiin ng g tth hee d drriillll.. Use gloves only when changing
hot bits and accessories to avoid burns.
H Haam mm meerr b biittss aan nd d tto oo ollss g geett h ho ott d du urriin ng g o op peerraattiio on n.. Wear gloves when touching them.
D Do o n no ott u ussee iin n d daam mp p o orr w weett llo occaattiio on nss.. D Do o n no ott o op peerraattee tto oo oll iin n aan n eexxp pllo ossiivvee
aattm mo ossp ph heerree, such as in the presence of flammable liquids, gases or dust.
Power tools create sparks, which may cause an explosion or fire.
S SY YM MB BO OL LS S
IIM MP PO OR RT TA AN NT T:: Some of the following symbols may be used on your tool. Please
study them and learn their meaning. Proper interpretation of these symbols will
allow you to operate the tool better and safer.
S SY YM MB BO OL L N NA AM ME E E EX XP PL LA AN NA AT TIIO ON N
V Volts Voltage (Potential)
A Amperes Current
Hz Hertz Frequency (Cycles per Second)
W Watt Power
Kg Kilograms Weight
Alternating Current Type of Current
Direct Current Type of Current
Alternating or Direct Current Type of Current
Earthing Terminal Grounding Terminal
Class II Construction Denotes Double Insulation
min Minutes Time
s Seconds Time
␾ Diameter Size of Drill Bits,
Grinding Wheels, etc.
No load speed No-load Rotational Speed
.../min Revolutions per Minute Revolutions, Surface Speed,
Strokes, etc. per Minute
1,2,3, … Ring Selector Settings Speed, Torque or Position Settings
1
3
11
10
7
6
12
5
4
8
2
9
10. Chuck Key
11. Chuck Key Holder
12. Power Cord
7