Kawasaki 840223 - Manual (Page 7)

R RE EM MO OV VIIN NG G // A AT TT TA AC CH HIIN NG G B BA AT TT TE ER RY Y P PA AC CK K
R RE EM MO OV VE E B BA AT TT TE ER RY Y P PA AC CK K::
1. Press both release buttons on
either side of the Impact Wrench to
release the battery pack.
2. Pull battery pack free of Impact
Wrench.
A AT TT TA AC CH H B BA AT TT TE ER RY Y P PA AC CK K::
1. Align the raised portion of the bat-
tery pack with the groove in the
battery compartment of the Impact
Wrench.
2. Press the battery pack into place.
Make sure the latches are securely
fastened. Do not use the Impact
Wrench if the battery pack is not
seated properly.
C CH HA AR RG GE ER R
B Beeffo orree u ussiin ng g b baatttteerryy cch haarrg geerr,, p plleeaassee rreeaad d ccaarreeffu ullllyy aallll
iin nssttrru uccttiio on nss aan nd d ccaau uttiio on naarryy m maarrkkiin ng gss o on n b baatttteerryy cch haarrg geerr,, b baatttteerryy p paacckk aan nd d
p prro od du ucctt u ussiin ng g b baatttteerryy..
T Th hee cch haarrg geerr w wiillll n no ott aau utto om maattiiccaallllyy ttu urrn n ““O OFFFF”” w wh heen n tth hee
b baatttteerryy p paacckk iiss ffu ullllyy cch haarrg geed d.. The charging indicator light will remain ““O ON N””
until the charger is disconnected from the electrical outlet.
U Ussee o on nllyy tth hee cch haarrg geerr w wh hiicch h aacccco om mp paan niieed d yyo ou urr p prro od du ucctt o orr d diirreecctt rreep pllaacceem meen ntt aass
lliisstteed d iin n tth hiiss m maan nu uaall.. Do not substitute any other charger. Use only Alltrade
approved chargers with your product.
D Do o n no ott d diissaasssseem mb bllee cch haarrg geerr..
D Do o n no ott u ussee cch haarrg geerr iiff iitt h haass b beeeen n d daam maag geed d,, lleefftt o ou uttd do oo orrss iin n tth hee rraaiin n,, ssn no ow w,, w weett
o orr d daam mp p een nvviirro on nm meen nttss,, o orr iim mm meerrsseed d iin n lliiq qu uiid d..
T Th hee b baatttteerryy p paacckk aan nd d cch haarrg geerr h heeaatt d du urriin ng g cch haarrg giin ng g.. Place the charger on a flat,
non-flammable surface away from flammable materials with at least four inches of
clearance to allow proper air circulation around the charger and battery pack.
W Wh heen n tth hee b baatttteerryy p paacckk rreeq qu uiirreess rreecch haarrg giin ng g,, aa 3 3--5 5 h ho ou urr cch haarrg gee aallllo ow wss tth hee tto oo oll tto o
o op peerraattee aatt ffu ullll p po ow weerr.. A charging indicator light on the charger will illuminate to
show that charging is taking place.
C CH HA AR RG GIIN NG G B BA AT TT TE ER RY Y P PA AC CK K
C CH HA AR RG GE E B BA AT TT TE ER RY Y P PA AC CK K::
1. Make sure the trigger on
the Cordless Impact
Wrench is in the ““O
OFFFF””
position and remove the
battery pack from the
Impact Wrench.
2. Insert the battery pack into the
charger. Be sure that the battery
pack is fully seated in the charg-
er. Do not force.
3. Plug the charger into the nearest
120 volt, electrical outlet. The
indicator light will come ““O
ON N””.
IIM MP PO OR RT TA AN NT T IIN NFFO OR RM MA AT TIIO ON N FFO OR R R RE EC CH HA AR RG GIIN NG G H HO OT T B BA AT TT TE ER RIIE ES S
When using your Cordless Impact Wrench continuously, the batteries in your bat-
tery pack will become hot. You should let a hot battery pack cool down for approx-
imately 30 minutes before attempting to recharge. When the battery pack becomes
discharged and is hot, the red light on the charger will flash. When the battery pack
cools down, the red light will glow continuously.
T Th hiiss w wiillll o occccu urr w wh heen n cco on nttiin nu uo ou uss u ussee o off yyo ou urr C Co orrd dlleessss
IIm mp paacctt W Wrreen ncch h ccaau usseess tth hee b baatttteerryy p paacckk tto o b beecco om mee h ho ott.. It does not occur
under normal circumstances.
A AS SS SE EM MB BL LY Y
B Bee aaw waarree tth haatt tth hiiss tto oo oll iiss aallw waayyss iin n aan n o op peerraattiin ng g cco on nd dii--
ttiio on n b beeccaau ussee iitt d do oeess n no ott h haavvee tto o b bee p pllu ug gg geed d iin ntto o aan n eelleeccttrriiccaall o ou uttlleett.. Always
turn the switch ““O OFFFF”” and remove the battery pack before changing bits.
12
RELEASE
BUTTON
BATTERY PACK
LED LIGHT
BATTERY
CHARGER
120V AC
ADAPTER