Kambrook Jaguar KBV50 User Manual
Page 3
alwayS enSure tHat tHe
duSt contaIner and tHe
motor protectIon fIlter
are correctly fItted. neVer
operate wItHout tHe duSt
contaIner and fIlterS In
place.
VarIaBle power control
The power booster dial on the unit is to
be used for variable power control. Turn
the control clockwise for maximum power
for vacuuming hard floor and carpet
surfaces. Turn the control anti-clockwise
for minimum power when using the
crevice and brush tools.
creVIce and BruSH tool
acceSSorIeS
The crevice tool is ideal for vacuuming
hard to reach places such as the edges
along skirting boards.
The brush tools can be used to vacuum
delicate surfaces and areas such as shelves
and venetian blinds.
Set the variable speed control between
minimum and medium power when using
the tool accessories.
Turn off the vacuum cleaner when
changing any attachments.
duSt contaIner IndIcator
and dISpenSIng tHe duSt
contaIner
The dust container should be emptied
when the dust and dirt reaches the MAX
level.
Always switch the appliance off, then
switch off at the power outlet and unplug
the appliance prior to replacing filters or
emptying the dust container.
To remove the dust container, ensure the
unit is down on its wheels; Remove the
dust container by pressing down on the
“Press and Lift” button
on/off
cord
press
& lift
up
down
on the dust
container. Once released slowly pull the
container upwards.
To empty the dust container simply place
it above the rubbish bin; press the “push
to empty” button. The bottom of the
container will release and the dust and
compiled dirt will be dispensed.
uSIng your KamBrooK
Jaguar Vacuum cleaner
When unpacking the vacuum cleaner unit
check to see you have received all the
required components, such as the hose
and other accessories before discarding
the packaging.
Ensure that the dust container and filters
are correctly fitted.
Locate the crush proof hose and push
the connection point into the hose inlet
connection on the front side of the unit,
until a “click” sound is heard.
Connect the wide end of the metal wand
to the hose end, and push together firmly.
Fit the floor tool to the narrow end of the
wand and push together firmly.
Fully extend the power cord by pulling
the power plug (situated at the rear of the
unit) out from the unit, until the yellow
tape on the cord is shown.
ENSURE THAT YOU DO NOT OVER
EXTEND THE POWER CORD - DO
NOT EXTEND PAST THE RED
WARNING TAPE ON THE CORD
Plug into a 230/240v power point and
switch the power on.
To commence vacuuming push down on
the on/off button
on/off
cord
press
& lift
up
down
at the top of the unit.
When vacuuming is complete, push down
on the ‘on/off’ button to switch off. Turn
the power off at the outlet and then
remove the power cord from the power
outlet. When removing plug from the
power outlet grasp the plug not the cord.
To retract the cord push down on the
‘cord rewind’
on/off
cord
press
& lift
up
down
to retract the cord.
IMPORTANT: HOLD THE PLUG END
WHEN RETRACTING THE CORD TO
PREVENT IT FROM STRIKING YOU OR
THE VACUUM.
IMPORTANT: DO NOT USE THE UNIT
WITHOUT A DUST CONTAINER IN
PLACE
cleanIng and replacIng
fIlterS
Filters must be cleaned from time to time
to remove the fine dust particles that have
been collected.
1. Remove the dust container from the unit
by pressing down on the “Press and Lift”
button
on/off
cord
press
& lift
up
down
2. Then press the “Push to Empty” button.
The bottom of the container will
release. Take off the filter bracket by
holding onto the shaft and turning the
filter in an anti-clockwise direction and
the filter and its bracket will be released.
3. To remove the metal filter bracket,
simply lift it vertically. The filter bracket
can be rinsed in luke warm water.
Ensure you let the filter bracket
completely dry naturally before next use.
4. Shake and tap the HEPA filter until
all the fine dust particles are removed.
However, after approximately 6 months
the HEPA filter should be replaced.
5. To place the filter back in the dust
container simply place the metal filter
bracket directly over the HEPA filter,
ensure that the metal filter holder is
completely dry before use. Ensure that
the grooves on the HEPA filter holder
and metal filter bracket fit into place.
6. Simply place the filter unit in the dust
container lid and turn the filter unit in
a clockwise direction until it is clicked in
place. Close the bottom of the container.
7. Place the dust container back in the
vacuum cleaner for next use.
KBV50.indd 4-5
9/5/07 11:42:25 AM