Specifications, Options, Applicable mil-std & ip – Kenwood FleetSync TK-7150 User Manual
Page 2: Kmc-9c, Kmc-27a, Kmc-27b, Kmc-28a, Kct-18, Kct-22, Kct-23

ADS#26608 Printed in USA
JQA-QMA1205
Specifications
Applicable MIL-STD & IP
Model
TK-7150
TK-8150
GENERAL
Frequency Range
Type1:
136~174MHz
450~500MHz
Number of Channels (Zone)*
Conventional CH:
Max.128 (1 zone x 128ch ~ 128 zones x 1ch)
Trunking ID:
Max. 250/zone (max.32 zones)
Channel Spacing
Wide:
25kHz, 30kHz
25kHz
Narrow:
12.5kHz, 15kHz
12.5kHz
Operating Voltage
13.6V DC±15%
Current Drain
Standby:
0.5A
0.5A
Receive:
2.3A
2.3A
Transmit:
Less than 12A
Less than 13A
Duty Cycle
Transmit: 20%
Operating Temperature Range
-22
ºF ~ +140ºF (-30ºC ~ +60ºC)
Frequency Stability
±0.00025%
(-22
ºF ~ +140ºF)
Antenna Impedance
50
Ω
Dimensions (W x H x D)
7-1/12” x 2” x 7”
(180mm x 50mm x 170mm)
Weight (net)
5.9 lbs (2.7kg)
FCC ID
ALH32273110
ALH32283110
Band Spread
38MHz
50MHz
Model
TK-7150
TK-8150
RECEIVER (Measurements made per EIA/TIA-603)
Sensitivity
12dB SINAD:
0.35µV
20dB Quieting:
0.45µV
Selectivity
Wide:
84dB (±30kHz)
80dB (±25kHz)
Narrow:
76dB (±15kHz),
73dB (±12.5kHz)
76dB (±12.5kHz)
Intermodulation
Wide:
77dB (±30, 60kHz)
79dB (±25, 50kHz)
Narrow:
75dB (±15, 30kHz)
73dB (±12.5, 25kHz)
Spurious Response
85dB
Audio Output
External:
12W (@ 4
Ω 3% distortion)
13W (@ 4
Ω 5% distortion)
Internal:
3.2W (@ 16
Ω 3% distortion)
3.5W (@ 16
Ω 5% distortion)
TRANSMITTER (Measurements made per EIA/TIA-603)
RF Output Power
50 to 15 watts
45 to 15 watts
High:
50 watts
45 watts
Low:
15 watts
15 watts
Type of Emission
Wide:
16K0F3E, 20K0F1D
Narrow:
11K0F3E, 11K2F1D
Spurious Response
75dB
FM Hum & Noise
Wide:
48dB
Narrow:
42dB
Microphone Impedance
600
Ω
Audio Distortion
Less than 1% at 1000Hz
■
KMC-9C
Desktop Microphone
■
KMC-27A
Microphone
(noise-canceling)
■
KMC-27B
Microphone
■
KMC-28A
Keypad Microphone
(noise-canceling)
■
KCT-18
Ignition Sense Cable
■
KCT-22
Remote Control Cable
8 feet
17 feet
25 feet
■
KCT-23
DC Power Cable
Medium Power
Dash (10 feet)
Medium Power Remote
(Positive: 23 feet,
Negative: 3.3 feet)
■
KES-5
External Speaker
■
KLF-2
Line Filter
■
KPS-10A
Regulated DC
Power Supply
■
KPS-15
DC Switching
Power Supply
■
KRK-9
Single Control Head
Remote Kit
Options
All accessories and options may not be available in all markets. Contact an authorized
Kenwood dealer for details and complete list of all accessories and options.
Standard
MIL 810C
MIL 810D
MIL 810E
MIL 810F
Methods/Procedures
Methods/Procedures
Methods/Procedures
Methods/Procedures
Low Pressure
500.1/Procedure I
500.2/Procedure I, II
500.3/Procedure I, II
500.4/Procedure I, II
High Temperature
501.1/Procedure I, II
501.2/Procedure I, II Cat. A1
501.3/Procedure I, II Cat. A1
501.4/Procedure I, II
Low Temperature
502.1/Procedure I
502.2/Procedure I, II Cat. C1
502.3/Procedure I, II Cat. C1
502.4/Procedure I, II
Temperature Shock
503.1/Procedure I
503.2/Procedure I Cat. A1, C1
503.3/Procedure I Cat. A1, C1
503.4/Procedure I, II
Solar Radiation
505.1/Procedure I
505.2/Procedure I
505.3/Procedure I
505.4/Procedure I
Rain
506.1/Procedure II
506.2/Procedure II
506.3/Procedure II
506.4/Procedure III
Humidity
507.1/Procedure II
507.2/Procedure II
507.3/Procedure II
507.4
Salt Fog
509.1/Procedure I
509.2/Procedure I
509.3/Procedure I
509.4
Dust
510.1/Procedure I
510.2/Procedure I
510.3/Procedure I
510.4/Procedure I, III
Vibration
514.2/Procedure VIII, X
514.3/Procedure I Cat. 8
514.4/Procedure I Cat. 8
514.5/Procedure I Cat. 20
Shock
516.2/Procedure I, II, III, V
516.3/Procedure I, IV, V
516.4/Procedure I, IV, V
516.5/Procedure I, IV, V
Kenwood follows a policy of continuous advancement in development.
For this reason specifications may be changed without notice.
* During simultaneous operation of conventional and LTR
®
modes.
Conventional channel/trunking ID can be programmed up to 512.
footnotes from Front:
1
KRK-9, KCT-22M/M2/M3, KCT-23M/M3
remote control options required.
2
6-Pin Accessory Connector for external
speaker, PA Output & ignition sense input.
3
KCT-18 ignition sense cable option required;
plugs into mobile 6-pin jack ignition sense input.
4
Built-in PA/HA outputs (no option board
required); Horn Alert operates for 2-Tone or
DTMF selective call decode only.
5
Short Text Messages are radio stored & LCD
displayed; Long Text Messages require a
KDS-100 and KCT-40.
6
FleetSync
®
GPS features require an internal
GPS board or externally wired GPS receiver
with NMEA TTL level serial data output to
the internal COM 1 or 2 set to "GPS".
FleetSync
®
is a trademark of Kenwood Corporation.
LTR
®
is a registered trademark of Transcrypt International.