Silvercrest PS2-WLC User Manual

Page 2

PS2-WLC Controller

- 2 -

Note:

Please only use batteries or rechargeable batteries with a nominal voltage of 1.5 V.

Please ensure the batteries are always inserted according to the correct polarity. Replace

the batteries with the same brand or similar batteries.

There is a risk of explosion if the batteries are not replaced correctly.

Do not attempt to recharge a non-rechargeable battery. There is a risk of explosion.

Batteries / rechargeable batteries can be fatal if swallowed. Please store batteries out of

reach of small children. Seek medical help immediately if a battery has been swallowed.

Do not expose the batteries to heat or flames. Never short-circuit batteries; never try to

force open batteries; never attempt to recharge non-rechargeable batteries. Batteries may
otherwise explode and cause serious injury.

Never replace the batteries in a potentially explosive area. Sparks may be generated

while the batteries are being inserted or replaced which could cause an explosion.
Potentially explosive areas are often signposted as such, but not always. These include
filling stations, such as under below-deck areas on boats, fuel transmission stations, fuel
depots, areas in which the air may contain chemicals or particles such as grain, dust or
metallic powder, as well as all other areas in which you would normally be asked to switch
off the engine of your car.

Switching on and off

The on/off switch is on the back of the device. To switch the unit off move the

switch to the “OFF” position and to the “ON” position to switch it on.

Connecting the controller

The connection mode will initiate as soon as the

On/Off switch

on the underside of

the unit is switched to the ON position. The

RX-LED

and

ODE

-LED

lights will

light up briefly at the same time. If the

RX-LED

comes on, the device is trying to establish a

connection with the receiver. The

LED

goes out as soon as a connection has been

established.

Force connection

If several wireless controllers are connected at the same time, you can use the force
connection method to select a single controller.
Press the

ONNECT

button on the hand-held unit and then press the

ONNECT

button

on the receiver within 15 seconds to establish a connection. Now press the

button

and the

ELECT

button on the hand-held unit and the

ONNECT

button on the

receiver at the same time for 15 seconds.

Mode selection

Many games support an analogue controller which permit more precise input than with digital
controllers.
There must be a connection to the receiver before you can switch between the digital and
analogue modes. To do this, press the

NALOGUE

button . The

ODE

-LED

lights

up in analogue mode. The

ODE

-LED

is off in digital mode.

Note:

The default mode is digital.

Not all games support digital mode.

You may have to finish the game before switching between modes.

10.

Energy-saving mode

The unit is equipped with an energy-saving mode to conserve energy and prolong battery life.
This mode is activated in the following situations:

where no connection has been established between the unit and the receiver after 3

seconds

where the unit and receiver are connected but the unit has not been used for 3 minutes

where the connection between controller and receiver has been interrupted and no

connection has been established within 6 seconds

where you press the

ONNECT

button on the hand-held unit without pressing the

ONNECT

button on the receiver within 15 seconds.

If your unit is in the energy-saving mode, press either the

TART

, or

buttons to reactivate the controller.

11.

TURBO functions

With the TURBO function you can switch the U, {, X, ,

R1,

R2,

and

buttons

to the TURBO/rapid fire function. The controller must be connected to the receiver to activate
or deactivate the TURBO function.

To activate: Press and hold the

URBO

button

until the

RX-LED

comes on.

Then press the button for which you want to activate the

rapid fire function

To deactivate: First press the button which you want to reset. Press and hold the

URBO

button

until the

RX-LED

goes out.