Stanton CMP.800 User Manual

Page 11

21. REV. Knob: Activates reverse playback function to play the track or sampler in reverse. Press the button again to

deactivate this effect.

22. FOLDER Knob: Turn FOLDER knob to search for the desired folder.

23. EJECT Button:

Pressing this will eject the CD. The eject function will only when the unit is in cue or pause mode, this is

to prevent

accidentally

ejecting the disc when in play mode.

24. RELOOP Button: If a SEAMLESS LOOP has been made, but the CD player is not currently in seamless loop mode,

pressing the RELOOP button will instantly reactivate the seamless loop mode. To exit loop, press the OUT button.

RELOOP will appe

ar in the VFD display when the RELOOP function is available.

In the loop mode, hold OUT button, LED of OUT/RELOOP will flash and “OUT EDIT” will be shown on the VFD, now you

can turn the JOG wheel to edit out point; then press the OUT button again to exit editing.

25. OUT Button: This button is used to set the end point of a loop. A loop is started by pressing the IN button, pressing the

OUT button set the loop ending point. The loop will continue to play until the OUT button is pressed once again.

26. IN Button: This function allows you to set a CUE POINT without music interruption. This button also sets the starting

point of a seamless loop.

27. EFFECT and HOLD Butt

on(s)

HOLD Button -‐ This button allows you to set and lock any new parameters you set to the effects. This button will glow

when the hold function is activated. If the hold function is not selected any changes to the effect parameters will be

momentary.

ii)

PARAMETER TIME Button -‐ This button is used to adjust the parameter time value. You can also push the TIME knob.

LED on, and turn the JOG wheel to adjust the parameter time value.



If the hold function is not selected any changes to the effect parameters will be momentary.



During hold function is selected the auto beat sync will be turned off.

ECHO Effect -‐ This button is used to activate and deactivate the echo effect. The echo effect adds an echo to your output

signal.

FLANGER Effect -‐ This button is used to activate and deactivate the flanger effect. The flanger effect layers a short delayed

version of the original track to the output signal to create an effect similar to a jet taking off.

FILTER Effect -‐ This button is used to activate and deactivate the filter effect. The filter acts like a very powerful sweeping EQ

with resonance.

PARAMETER RATIO Button -‐ This button is used to adjust the parameter ratio value. You can also push the RATIO knob, LED

on, and turn the JOG WHEEL to adjust the parameter ratio value.

AUTO LOOP Button -‐ Press this button to activate AUTO LOOP function. Press IN button, and OUT point will be found

automatically according to the BPM value.

28. MIDI A/B: Under the MIDI mode, press this button to switch PLAYER A/B.

29.

SGL/CTN Button

This function allows you to choose between single or continue track play (all tracks in order). This

function also operates in RELAY mode. With this button you can also switch auto cue on and off, by pressing it for at

least 1 sec.

30. TIME Button:

The button will switch the time value described in the TIME Meter between ELAPSED playing time, TRACK

Remaining time and TOTAL Remaining time.

31.

se this button to

select FX SYNC or LOOP SET.

FX SYNC -‐ This is used to select the delay time of an effect to th

e beat of music. The beat delay rations are 1/4, 1/2, 3/4,

1/1, 2/1, and 4/1. To turn off auto beat sync press

button for 1 sec.

LOOP SET -‐ When the loop set function is activated, select the beat of 1/2, 1, 2, 4, 8, 16 (1 bar=4 beat) at which you

would like to end your desired loop.

32. SHIFT Button: Hold the SHIFT button enables to call up a second function.