Stellar Industries SI-60 - Manual (Page 48)

42 Stellar Cable Hoist Owner’s Manual
Step 16: Apply Decals
Item PN Description Suggested Location
1
2
3
C5910 DECAL STELLAR LOGO 3.75X9.00
4
5
7
6 45553 DECAL WARNING RAISED HOIST
8
9
45691 DECAL HOIST INSTRUCTIONS
10
45692 DECAL WARNING CONTAINER
11
45693 DECAL CAUTION OPERATION
12
52556 DECAL PROP INSTRUCTIONS
13
45695 DECAL WARNING UNEVEN GROUND 14
45696 DECAL DANGER POWER LINES HOIST 15
45697 DECAL CAUTION PTO SPEED 17
25627 DECAL CRUSH POINT
18
45698 DECAL WARNING CABLE
45726 DECAL WARNING HYDRAULIC SAFETY
45557 DECAL DANGER STAND CLEAR
C5942 PLATE SERIAL # STELLAR TRUCKS Mounted on hoist rail as shown above. (Not included in kit)
On hoist rail as shown above.
Both sides - On hoist rail as shown above. (Ship Qty 1 Loose)
Both sides - On hoist rail as shown above.
Both sides - On hoist rail as shown above.
Both sides - On hoist rail as shown above.
Both sides - On hoist rail as shown above.
On hoist rail as shown above.
On reservoir near controls. (Not Shown)
On reservoir and in cab. (Not Shown)
On reservoir and in cab. (Not Shown)
On reservoir and in cab. (Not Shown)
On reservoir. (Not Shown)
On reservoir and in cab. (Not Shown)
On reservoir. (Not Shown)
In cab near PTO control. (Not Shown)
In cab near hoist up light. (Not Shown)
45699 DECAL ICC BUMPER REQUIREMENT
45906 DECAL HOIST UP
35234 DECAL STELLAR MADE IN THE USA
Qty.
3
2
1
52790 DECAL VB CONTROL
16
On reservoir near controls. (Not Shown - Cable75 Models) 1
2
1
2
2
2
1
6
2
1
2
1
1
1
1
7
6
2
1
3
4 4 4 8
5
MODEL NO. SERIAL NO. DATE MADE IN THE U.S.A. BY STELLAR INDUSTRIES, INC. PN C5942 THE FOLLOWING U.S. OR FOREIGN PATENTS MAY APPLY: U.S. PATENTS 6,749,389 6,558,104 5,427,495
5,108,247 6,065,942 5,082,417 CANADIAN PATENTS 6,749,389
5,108,247
WARNING CRUSHING HAZARD
Moving parts can crush and cut. Keep hands and arms clear. 25627 WARNING CRUSHING HAZARD
Moving parts can crush and cut. Keep hands and arms clear. 25627 WARNING CRUSHING HAZARD
Moving parts can crush and cut. Keep hands and arms clear. 25627 1. Raise prop upright until it hits the stop tab. 2. Lower hoist until frame rests on prop. 3. CAUTION: Do not power hoist down on prop. 4. To lower the prop - raise hoist and lower prop. 5. CAUTION: Any damage to prop should be properly repaired or replaced before using. 6. Be alert and think safety.
HOIST PROP OPERATING INSTRUCTIONS
PN 52556 35234 Proudly Designed and Manufactured in the USA by ®
DANGER STAND CLEAR WHEN THIS UNIT IS IN OPERATION! FAILURE TO DO SO COULD RESULT IN SERIOUS PERSONAL INJURY. 45557
WARNING BEFORE WORKING AROUND A RAISED HOIST, THE HOIST MUST BE SUPPORTED BY THE HOIST PROP. (SEE HOIST PROP OPERATING INSTRUCTIONS) FAILURE TO DO SO COULD RESULT IN SERIOUS INJURY OR DEATH.
IF THE HOIST PROPS CANNOT BE USED, CONSULT THE MAINTENANCE
SECTION OF THE OPERATION MANUAL
FOR THE PROPER PRECAUTIONS. 45553
WARNING
BEFORE WORKING AROUND A RAISED HOIST, THE HOIST MUST BE SUPPORTED BY THE HOIST PROP. (SEE HOIST PROP OPERATING INSTRUCTIONS) FAILURE TO DO SO COULD RESULT IN SERIOUS INJURY OR DEATH. IF THE HOIST PROPS CANNOT BE USED, CONSULT THE MAINTENANCE SECTION OF THE OPERATION MANUAL FOR THE PROPER PRECAUTIONS. 45553
24" OR LESS
ICC BUMPER REQUIREMENT THE LOAD AND/OR TRUCK RAILS MUST NOT EXTEND PAST THE TRUCK BUMPER MORE THAN 24 INCHES. (See Federal Motor Carrier Safety Regulation 393.86)
45699
2
1
3
4
5 6
MODEL NO. SERIAL NO. DATE
MADE IN THE U.S.A. BY STELLAR INDUSTRIES, INC. PN C5942 THE FOLLOWING U.S. OR FOREIGN PATENTS MAY APPLY: U.S. PATENTS 6,749,389 6,558,104 5,427,495 5,108,247 6,065,942 5,082,417 CANADIAN PATENTS 6,749,389 5,108,247
WARNING CRUSHING HAZARD Moving parts can crush and cut. Keep hands and arms clear. 25627
1. Raise prop upright until it hits the stop tab. 2. Lower hoist until frame rests on prop. 3. CAUTION: Do not power hoist down on prop. 4. To lower the prop - raise hoist and lower prop. 5. CAUTION: Any damage to prop should be properly repaired or replaced before using. 6. Be alert and think safety.
HOIST PROP OPERATING INSTRUCTIONS
PN 52556
35234 Proudly Designed and Manufactured in the USA by ®
Note: Approximate placement as shown.
PN 52791