Samson XM910 - Manual (Page 7)

Front Panel Layout
5
FRONT PANEL
1
AUX 1 MONITOR
– Controls the amount of signal sent
to the monitor amp and AUX
1 send jack.
2
AUX 2/EFX
– Controls the amount of signal sent to the
digital effects processor and AUX
2 send jack.
3
HIGH FREQUENCY
– Controls the amount of treble
applied to that channel.
4
MID FREQUENC
Y – Controls the amount of midrange
applied to that channel.
5
LOW
FREQUENCY
– Controls the amount of bass
applied to that channel.
6
PAN (Balance on stereo channels)
– Adjusts the
amount of signal sent to the Left or Right bus.
7
PEAK LED
– Indicates that the signal is peaking
or overloading.
8
GAIN
– Sets the overall level for the Mic or Line
input.
9
VOLUME
– Controls the overall volume of that chan-
nel.
10 LINE
INPUT
– Balanced input for line level sig
nals.
11
MIC INPUT
– Input connector for low impedance bal-
anced microphone input.
12 EFX
LEVEL
– Master control for the amount of signal
sent to the DSP and AUX
2 Send.
13 EFX
BYPASS
– Shuts off the internal DSP.
14
SELECT
– Selects one of the 100 digital effects pre-
sets available.
15
EFX PROGRAM DISPLAY
– Show the current DSP
effect pre-set.
16
MAIN LED METERS
– Indicates the amount of output
signal on the main stereo output.
32
DJ
CROSSFADER
– Used to mix between the
CD1 and CD2 inputs.
33
REC OUT
– Output used to send main mix to an
external recorder.
34
CD2 INPU
T – Used to connect input from a
CD/MD/Tape Deck.
35
CD2 INPUT VOLUME
– Controls the amount of
volume from an external line source like CD, MP3 or Tape.
36
CD1 INPUT
– Used to connect input from a
CD/MD/Tape Deck.
37
CD1 INPUT VOLUME
– Controls the amount of
volume from an external line source like CD, MP3 or Tape.
38
AUX 1 SEND
– Monitor signal output connector.
39
MIX OUT
– Left and Right output jacks for the
main mix output pre amp signal.
40
AMP
IN
– Left and Right input jacks for connect-
ing directly to the internal power amplifier.
41
EFX FOOTSWITCH
– Switches the effects on or
off.
42
AUX 2 SEND
– Effects output jack for connecting
an external effects processor.
43
EFX
RETURN
– Left and Right input connectors
for mixing external signals.
44
PEAK
LIMTER
SWITCH
– Use to engage the inter-
nal Peak Limiter.
45
LINE
/ MIC INPUT
(Stereo Channels) –
Combination connector with 1/4-inch TRS (TIP RING
SLEEVE) input to the right line input, plus
XLR mic input.
45
LINE
L INPUT (Stereo Channels)
– 1/4-inch TRS
(TIP
RING
SLEEVE) input to the left line input.
17
MONITOR LED METER
– Indicates the amount of
output signal on the monitor output.
18
CLIP LEDS
– Indicates power amp maximum level.
19
AMP 1 and AMP 2 PROTECT LED
s – Indicates
power amp is in overload and that the protect cir- cuit is active.
20 PHANTOM
POWER
– Provides 48 volts to the XLR
inputs for powering condenser microphones.
21
MUTE
CH 1 - 6 SWITCH
– Used to turn off the inputs
of channel 1 through 6.
22 MODE
SWITCH
– Configures the output of the
power amps. Stereo or Main/Monitor 450W X 2 (4 ohms), Main Bridged 600W X 1 (8 ohms).
23
POWER LED
– Indicates status of the power switch
On/Off.
24
MONITOR
GRAPHIC EQ
– Provides dual 10-Band
equalization for the channel monitor.
25
EFX TO
MON
– Effects return control for monitor
channel.
26
MASTER (MONITOR)
– Master volume control for
monitor amp and AUX 1 Send.
27
LOW
CUT (MONITOR)
– Used to attenuate the low
frequencies below 75 Hz on the monitor output.
28
EFX RETURN (MAIN)
– Effects return control for
main channel.
29
MASTER
– Master volume control for main
stereo/mono amp and main mix out L/R.
30
MAIN
GRAPHIC EQ
– Provides dual 10-Band
equalization for the channel monitor.
31
LOW
CUT (MAIN)
– Used to attenuate the low fre-
quencies below 75 Hz on the main output.