Symphonic SC720FDF - Manual (Page 17)

17
EN
INDEX SEARCH
0 3
TIME SEARCH
2 : 50
TIME SEARCH
TV/VCR TV/VCR This function allows you to quickly
advance the tape to your desired posi-
tion simply by entering the exact amount of playback
time you want to skip.
In the example below: To watch a program before/
after 2 hour 50 minutes from the present position,
in either direction.
1
Press [SET-UP].
Use [
K K / L L ] to point to "TIME
SEARCH", then press
[ENTER].
2 Use [ K K / L L ] until your desired
time appears.
To cancel the Time Search at
this point, press [SET-UP].
NOTE:
• Time Search can be set up to a maximum of 9 hours
50 minutes (9:50) by 10 minutes at a time.
3
Use [s s / B B ] to rewind or fast forward to the
specified point.
The time counts down during the search. When
the counter reaches "0:00:00", the tape will start
playback automatically.
TO CANCEL DURING TIME SEARCH
Press [STOP/EJECT C /A] on the unit or [STOP C C ].
- TV/VCR SETUP -
TIMER PROGRAMMING
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
B TIME SEARCH
INDEX SEARCH
INDEX SEARCH
TV/VCR TV/VCR
This function allows you to index the
starting point to make it easy to reach
the point in either fast forward or rewind mode.
• Every time you start recording, an index is marked
automatically. The index mark also works as the
starting point of Timer recording and OTR.
• The index mark will not be recorded if [PAUSE F F ]
is used during recording.
• The time gap between making the index marks on
the tape should be greater than 1 minute for SP
recording, 2 minutes for LP recording and 3 min-
utes for SLP recording.
• In some cases, the index mark at the beginning of
video tape cannot be detected.
Example: You are watching program number 4 and
want to fast forward to program number
7. Skip three programs.
Pro.1 Pro.2 Pro.3 Pro.4 Pro.5 Pro.6 Pro.7
4 3 2 1 1 2 3
End of
the tape
Beginning of
the tape
CURRENT PLAYBACK PROGRAM
INDEX MARK
- TV/VCR SETUP -
TIMER PROGRAMMING
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
B INDEX SEARCH
1
Press [SET-UP].
Use [
K K / L L ] to point to
"INDEX SEARCH", then press
[ENTER].
2
Use [ K K / L L ] until the number
of programs that you want to
skip appears.
3 Use [s s / B B ]. The unit begins rewinding or fast
forwarding to the beginning of desired program.
4 When the search is completed, the unit will start
playback automatically.
• The numbers of Index Search can be set up to
20.
• This function is not available during recording.
TO CANCEL DURING INDEX SEARCH
Press [STOP/EJECT C /A] on the unit or [STOP C C ].
PICTURE SEARCH
TV/VCR TV/VCR This function is useful in finding or
skipping over a particular scene on a
tape. In this mode, the sound will be muted.
1
During playback, press [REV E E ] or [FWD D D ]
to view at a high speed (in forward/reverse).
2
Press [REV E E ] or [FWD D D ] again to view at
super high speed (in LP/SLP modes only).
NOTE:
• Tapes recorded in the SP or LP mode will normally
display a noise bar on the TV screen and the picture
may revert to black and white.
3 Press [PLAY B B ] to return to normal playback.
SPECIAL PLA
YB
A
CK / SEARCH FUNCTION
TV/VCR SECTION
T1203UD(EN/SP).QX3 06.2.15 7:14 PM Page 17