Speco Technologies SP-6NXC/T - Manual (Page 2)

Congratulations on your purchase of Speco Technologies’
Nexus Contractor™ 70/25 Volt Commercial Speaker
Systems!
Speco Technologies’ Nexus Contractor™ Commercial Speaker System Line offers premium quality
components and strong specification providing a network of sound and paging for the most
demanding commercial environments.
The high-end NXC Series features heavy-duty, industrial metal back cans that provides component
protection and safety while at the same time enhancing the speakers’ full-range bass sound as does
the speakers’ ported design.
Quick-snap terminal connects provide easy access and optimal angles for connecting speaker wire to
the NXC Series as a wattage selector dial makes transformer wattage setting as easy as a quick turn.
Added security loops mounted to the back can of the speakers allow for a support cable run.
Provided ceiling support brackets will complete a secure installation that will lend itself to countless
years of performance and reliability.
Nexus Contractor™ Commercial Speaker System Specifications:
Pre-construction:
Choosing Your Speaker Location and Pre-wiring the Job:
Carefully select areas of the ceiling where there are no obstructions, plumbing, heating/AC apparatus or
electrical wiring.
For sheetrock ceilings, use the enclosed C-Bracket as a cut out guide, tracing the inner dimensions of this
bracket on your sheetrock ceiling, then proceed to cut out the circle to establish mounting hole.
On drop ceiling installations where the ceiling tiles will not support the weight of the speaker, use
the accompanying pre-mounted brackets to support the weight of the speaker. Each bracket has two
elongated support brackets and a center C-Bracket that have dog-eared sides that rest on the elongated
support brackets and then are secured by the enclosed screws.
After selecting your brackets location, cut holes through the ceiling tile that line up perfectly with the
placement and diameter of the C-Brackets.
Upon finalizing speaker location and cutting holes, pre-run speaker wire through ceiling to be available
upon speaker installation.
Specifications:
• 4” Polypropylene Coated Woofer
with Rubber Surround
• 3/4” PEI Tweeter
• Frequency: 60Hz –20kHz
• 10 Watt RMS/ 30 Watt Max
• Sensitivity: 86 db 1w/1m
• Impedance: 8 ohms
• Transformer:
70/25 Volt Transformer Dial
• Transformer Settings:
10w/ 5w/2.5w/ 1.2w & 8 ohms
• Dimensions: 8” Dia x 8 1/2“ D
• Cut Out Dimension: 7” Dia
• Weight: 4.6 lbs.
• Quick-Snap Terminal Connects
• Metal Safety Loop for Securing
• Mounting Brackets Included
Specifications:
• 5.25” Polypropylene Coated Woofer
with Rubber Surround
• 3/4” PEI Tweeter
• Frequency: 50Hz –20kHz
• 60 Watts RMS/ 120 Watts Max
• Sensitivity 89 db 1w/1m
• Impedance: 8 ohms
• Transformer:
70/25 Volt Transformer Dial
• Transformer Settings:
60w/ 30w/ 10w/ 5w/ 2w & 8 ohm
• Dimensions: 9 3/4” Dia x 8 1/8 “ D
• Cut Out Dimension: 8 1/2” Dia
• Weight: 6.8 lbs.
• Quick-Snap Terminal Connects
• Metal Safety Loop for Securing
• Mounting Brackets Included
Item Code: SP-5NXC/T
5.25” 70/25V Commercial
Speaker System
Item Code: SP-6NXC/T
6.5” 70/25V Commercial
Speaker System
Specifications:
• 6.5” Polypropylene Coated Woofer
with Rubber Surround
• 3/4” PEI Tweeter
• Frequency: 50Hz –20kHz
• 60 Watts RMS/ 140 Watts Max
• Sensitivity: 90 db 1w/m
• Impedance: 8 ohms
• Transformer:
70/25 Volt Transformer Dial
• Transformer Settings:
60w/ 30w/ 10w/ 5w/ 2w & 8 ohm
• Dimensions: 10” Dia x 8 1/8 “ D
• Cut Out Dimension: 9” Dia
• Weight: 7.1 lbs.
• Quick-Snap Terminal Connects
• Metal Safety Loop for Securing
• Mounting Brackets Included
Item Code: SP-4NXC/T
4” 70/25V Commercial
Speaker System
Connecting and Mounting Your Speakers:
Please follow these directions for connecting and mounting your
Nexus Contractor™ Commercial Speaker System:
Easy Mount Tabs
Quick-Snap
Terminal
Connect
3/4”
Punch
Out
Hole Strain
Protector
Wattage
Tap Dial
Easy Mount Tabs
Adjusting Screws
Silver Wattage
Tap Dial Indicator
Terminal
Metal
Cover
Paint
Shield
™