Woodstock W1820 - Manual (Page 31)

-29-
Df[\cN(/(0&N(/)'D]^%J`eZ\()&('
J<
K
L
G
8c`^ed\ek
Qfe\
Jgi\X[\ifi
I`m`e^Be`]\
9cX[\
=`^li\*)% Spreader/riving knife alignment
zone.
+% Adjust the set screws to make sure the table insert
is flush with the table (use a straightedge as a
guide), then tighten the button head screw to secure
the table insert in place.
,. Place a straightedge against the blade and the
spreader. When properly aligned, the spreader/
riving knife will be parallel with the blade and in the
"Alignment Zone," shown in
=`^li\*).
— If the spreader/riving knife is not inside the
alignment zone and not parallel with the
blade, then it needs to be adjusted. Proceed to
"Adjusting Alignment
on GX^\-0.
— If the spreader/riving knife is not parallel with
the blade, it may be bent. Proceed to "Checking
Alignment
on GX^\-/ to determine if the
spreader/riving knife is bent.
;ljk:fcc\Zk`fe
To connect a dust collection hose, do these steps:
1. Fit a 4" dust hose over the dust port, as shown in
Figure 33, and tightly secure in place with a hose
clamp.
2. Tug the hose to make sure it does not come
off. Efk\1A tight fit is necessary for proper
performance.
:fdgfe\ekjXe[?Xi[nXi\E\\[\[1 Hkp
Dust Hose 4 " (not included) ...................................1
Hose Clamps 4" (not included) ................................2
Dust Collection System (not included) ......................1
;F EFK fg\iXk\ k_\ Df[\c N(/(0
fi N(/)' n`k_flk Xe X[\hlXk\ [ljk
Zfcc\Zk`fe jpjk\d% K_`j jXn Zi\Xk\j
jlYjkXek`Xc Xdflekj f] nff[ [ljk
n_`c\ fg\iXk`e^% =X`cli\ kf lj\ X [ljk
Zfcc\Zk`fe jpjk\d ZXe i\jlck `e j_fik
Xe[cfe^$k\idi\jg`iXkfip`cce\jj%
I\Zfdd\e[\[:=DXk;ljkGfik1+'':=D
;fefkZfe]lj\k_`j:=Di\Zfdd\e[Xk`fen`k_k_\iXk`e^
f]k_\[ljkZfcc\Zkfi%Kf[\k\id`e\k_\:=DXkk_\[ljk
gfik#pfldljkZfej`[\ik_\j\mXi`XYc\j1( :=DiXk`e^f]
k_\[ljkZfcc\Zkfi#) _fj\kpg\Xe[c\e^k_Y\kn\\ek_\
[ljkZfcc\ZkfiXe[k_\dXZ_`e\#* eldY\if]YiXeZ_\j
finp\j#Xe[+ Xdflekf]fk_\ifg\ec`e\jk_ifl^_flk
k_\jpjk\d%`jY\pfe[k_\jZfg\f]k_`jdXelXc%:fejlckXe\og\ikfi
gliZ_Xj\X^ff[[ljkZfcc\Zk`fe_fn$kfYffb%
=`^li\**% Dust hose attached to dust
port.