SECO-LARM USA Enforcer EV-1006-N4SQ - Manual (Page 2)

ENFORCER CCD IR Day/Night Camera Manual ENFORCER CCD IR Day/Night Camera Manual
Dimensions:
Optional Accessories:
Parts List
1 x IR camera with integrated
mounting bracket
3 x Mounting screws
3 x Screw anchors
1 x Manual
BEFORE STARTING
1. Please read this manual carefully and keep it for
future reference.
2. Use the camera within given temperature and
electricity limits.
3. Do not aim the LED light directly at the eyes when
the LEDs are on.
4. Do not point the camera at the sun. Heat could
damage the camera, even when not in use.
5. Do not mount the camera in areas exposed to
radiation, strong magnetic fields, or strong electrical
signals.*
INSTALLATION
1. Run a 12VDC power supply wire and a video cable
with a male BNC connector through the wall to where
the camera is to be mounted (if necessary).
2. Using the mounting screws and screw anchors,
attach the mounting base to the wall or ceiling where
the camera is to be mounted.
3. Connect the camera to the 12VDC power supply.
6. Do not open or disassemble the camera. There
are no user-serviceable parts inside.
7. Do not drop the camera or subject it to strong
vibrations.
* Note: Many video monitors produce strong
electromagnetic fields close to the display CRT,
especially when the monitor is turned on or during
de-Gaussing, which occurs automatically with
many monitors when the monitor is turned on.
Type
Chip
Resolution
Pickup elements
Scanning system
Sync
Video output
Lens
Minimum illumination
Gamma correction
S/N ratio
Shutter control
Backlight compensation
Automatic gain control (AGC)
Enclosure
# of infrared LEDs
Max. LED range
Power source
Power consumption
Operating temperature
Dimensions
Weight
Specifications A. Camera
B. Mounting base
C. 12” cord
D. DC jack*
E. BNC connector (female)
F. Adjustment collar
G. Locking screw
B
A
F D*
*Important:
Do not cut DC jack.
Use SECO-LARM’s
optional EVA-F5521-3
Pigtail Connector for
easy installation and
serviceability.
E
2 15 / 16 ” (74mm)
Color camera
1/3” CCD, Sony
420 TV lines
510 x 492 pixels (NTSC / EIA)
2:1 interlace
Internal
1Vp-p composite output, 75 ohms
4.3mm, F2.0 fixed
0.4 lux (LED off), 0.0 lux (LED on)
0.45
>50dB (AGC off)
Auto Electronic Shutter (AES) 1/60~1/100,000 sec. (NTSC)
On
Auto
IP66 weatherproof
18
Up to 60 ft. (18m)
12VDC±10%
100mA (IR off), 280mA (IR on)
14°~122° F (-10°~50° C)
6 1 /
4
”(L) x 2 15 /
16
”(D) (158 x 74 mm)
13.6 oz. (386g)
EV-1006-N4BQ/SQ/WQ
2 15
/ 16
” (
74
m
m
)
1 2 / 16 ” (52mm)
3 3 / 4 ” (95mm)
2 7
/ 16
” (
62
m
m
)
1 4 6 / ” (158mm)
C
G
4. Connect the camera’s female BNC connector to the
male BNC connector of the video cable.
5. Attach the camera to the mounting base by twisting
the adjustment collar and securing it to the plate.
6. Adjust the camera so the picture on the monitor
clearly displays the image from the camera.
7. Using the adjustment collar and locking screw,
secure the camera in place.
ENFORCER ®
EVT-PB1Q
O Passive Video Baluns.
O Up to 2,000 ft. range
over CAT5e UTP cables.
EVP-1SD4P9UL
O CCTV power supplies.
O 4, 9, 16 outputs available.
VG-1C12AQ
O Ground loop isolator.
ST-UV12-S0.5Q
O Full line of plug-in adapters.