Electr, Setting the cor – John Lewis JLBIOS601 User Manual
Page 10
10
Electr
Electr
Electr
Electr
Electronic Pr
onic Pr
onic Pr
onic Pr
onic Programmer
ogrammer
ogrammer
ogrammer
ogrammer
1 .
1 .
1 .
1 .
1 . “Time functions” control button
2 .
2 .
2 .
2 .
2 . Decreasing control button “ ”
3 .
3 .
3 .
3 .
3 . Increasing control button “ ”
4 .
4 .
4 .
4 .
4 . Display
5 .
5 .
5 .
5 .
5 . “Cooking duration” pilot lamp
6 .
6 .
6 .
6 .
6 . “End of cooking” pilot lamp
7 .
7 .
7 .
7 .
7 . “Minute timer” pilot lamp
8 .
8 .
8 .
8 .
8 . “Time” pilot lamp
The oven will work only if the time of day has been set.
However, the oven can also be operated without any programme.
Setting the cor
Setting the cor
Setting the cor
Setting the cor
Setting the corrrrrrect time of da
ect time of da
ect time of da
ect time of da
ect time of dayyyyy
When the power supply is switched on, or after a power failure, the “Time” pilot
lamp will flash on the display.
To set the correct time of day:
To set the correct time of day:
To set the correct time of day:
To set the correct time of day:
To set the correct time of day:
1 .
1 .
1 .
1 .
1 . Press button “ ” or “ ” (Fig. 1).
2 .
2 .
2 .
2 .
2 . After the setting is carried out, wait for 5 seconds: the “Time” pilot lamp
will go out and the display will show the set time. The appliance is ready for
use.
To reset the correct time of day:
To reset the correct time of day:
To reset the correct time of day:
To reset the correct time of day:
To reset the correct time of day:
1 .
1 .
1 .
1 .
1 . Press “Time functions” button repeatedly to select the time of day function.
The relevant pilot lamp will start flashing. Then proceed as described above.
The time of day can only be reset if no automatic function (Cooking duration
or End of cooking) has been set.
“““““Cooking duration
Cooking duration
Cooking duration
Cooking duration
Cooking duration””””” function
function
function
function
function
This function allows the oven to automatically switch off at the end of a
programmed cooking duration time. Place food in the oven, select a cooking
function and adjust the cooking temperature. Press “Time functions” button
repeatedly to select the “Cooking duration” function. The relevant pilot lamp
will start flashing (Fig. 2). Then, proceed as follows:
To set the duration time:
To set the duration time:
To set the duration time:
To set the duration time:
To set the duration time:
1 .
1 .
1 .
1 .
1 . Press button “ ” or “ ” (Fig. 3).
2 .
2 .
2 .
2 .
2 . After the setting is carried out, wait for 5 seconds: the "Cooking duration"
pilot lamp will come on and the display will revert to the time of day.
3 .
3 .
3 .
3 .
3 . When cooking time is over, the oven will be switched off automatically and
an acoustic alarm will be heard, while the pilot lamp will start flashing. Turn
the oven function and the thermostat control knob to zero.
To switch off the acoustic alarm, press any button.
NO
NO
NO
NO
NOTE:
TE:
TE:
TE:
TE: Turning the acoustic alarm off will reset the oven to manual, and if
the oven function and the thermostat knobs are not set to zero the oven
will start to heat again.
To cancel the duration time:
To cancel the duration time:
To cancel the duration time:
To cancel the duration time:
To cancel the duration time:
1 .
1 .
1 .
1 .
1 . Press “Time functions” button repeatedly to select the “Cooking duration”
function. The relevant pilot lamp will flash and the display will show the
remaining cooking time.
2 .
2 .
2 .
2 .
2 . Press button “ ” until the display shows “0:00”. After 5 seconds the pilot
lamp will go out and the display will revert to the time of day.
4
44
44
5
55
55
6
66
66
7
77
77
8
88
88
1
11
11
2
22
22
3
33
33
Fig. 3
Fig. 3
Fig. 3
Fig. 3
Fig. 3
Fig. 2
Fig. 2
Fig. 2
Fig. 2
Fig. 2
Fig. 1
Fig. 1
Fig. 1
Fig. 1
Fig. 1