Jacuzzi MAGNUM - Manual (Page 7)

Winterizing
Consult your dealer for advice on winterizing your
equipment if freezing temperatures occur in your locality.
His knowledge of your equipment makes him the best
qualified source of information. Follow his
recommendations, and if these include draining the filter
system, proceed as follows:
1. If your system does not contain a filter, proceed to
step2.
A. For sand filters: BACKWASH for 3 to 5
minutes and set dial valve to WINTERIZE.
B. For cartridge filters: Clean the filter element and
store in a dry place.
2. Drain system by loosening drain plugs (drain plugs
will drain without completely removing the plug
from unit) and/or removing pipe caps.
Water Chemistry
A proper and consistent use of chemicals is
necessary to maintain clean, sanitary water, prevent a
spread of germ infection and control the growth of algae
which can spoil the appearance and enjoyment of your
pool or spa.
Chlorine is the most commonly used chemical to
provide clean, sanitary water. Either dry or liquid chlorine
(calcium or sodium hypochlorite) can be used which
should be added daily as it is dissipated by dirt and germs
as well as be the sun and wind.
It is also important that the correct level of acidity or
alkalinity of the pool water be maintained. This is the pH
of your pool with pH 7.0 being neutral. Readings above
7.0 are alkaline and below are acid. A desirable range is
7.2 – 7.4.
Pump Maintenance
1. Motors are self-lubricating – no lubrication required.
2. Clean hair & lint strainer if you have a strainer body
pump.
3. Visually inspect motor for blockage of air vents on
motor shell. Remove any debris after breaker off.
4. Shaft seals may become worn and must be replaced if
leakage is observed.
Cleaning
Switch power off. Close valves in suction and return
line. Unscrew strainer Ring-Lok counterclockwise and
remove the strainer cover from hair and lint strainer and lift
out strainer basket. Clean and replace the basket. Take care
to seat basket properly. Clean O-Ring and re-lubricate with
petroleum jelly if necessary. Clean O-Ring seats on cover
and strainer. Refit cover and strainer – hand tighten only –
and open valves. Put pump back into operation.
Caution: Do not retighten strainer during operation.
Service & Repair Parts
Refer all service to your local dealer as his knowledge
of your equipment makes him the best qualified source of
information. Order all repair parts through your dealer. Give
the following information when ordering repair parts:
1. Unit nameplate data.
2. Description of part.
Trouble Shooting
MOTOR DOES NOT START
1. Disconnect switch or circuit breaker in OFF position.
2. Fuses blown or thermal overload open.
Locked motor shaft.
3. Motor windings burned out.
4. Defective starting switch inside single-phase motor
5. Disconnected or defective wiring
6. Low
voltage
MOTOR DOES NOT REACH FULL SPEED
1. Low voltage
2. 2 speed model set on low speed
3. Motor windings connected for wrong voltage on
dual voltage model.
MOTOR OVERHEATS (Protect trips)
1. Low voltage
2. Motor windings connected for wrong voltage on
dual voltage model.
3. Inadequate ventilation
PUMP DELIVERS NO WATER
1. Pump is not primed
2. Closed valve in suction or discharge line
3. Leakage or air into suction system
4. Impeller
clogged
LOW PUMP CAPACITY
1. Valve in suction or discharge line partly closed
2. Suction or discharge line partly plugged
3. Suction or discharge line too small
4. Pump running at reduced speed (see above)
5. Plugged basket in skimmer or hair and lint strainer
6. Dirty
filter
7. Impeller clogged
8. Wrong rotation (3 phase only)
LOW PUMP PRESSURE
1. Pump running at reduced speed (see above)
2. Wrong rotation (3 phase only)
3. Discharge valve or inlet fittings closed too much
HIGH PUMP PRESSURE
1. Discharge valve or inlet fittings closed too much
2. Return lines too small
3. Dirty
filters
NOISY PUMP AND MOTOR
1. Plugged basket in skimmer or hair in lint strainer
2. Worn motor bearings
3. Valve in suction line partly closed
4. Suction line partly plugged
5. Vacuum hose plugged or too small
6. Pump not supported properly
LEAKAGE OF WATER AT SHAFT
1. Shaft seal requires replacement
AIR BUBBLES AT INLEY FITTINGS
1. Leakage air into suction line at connections or valve
stem
2. Cover gasket of hair and lint strainer needs cleaning
3. Restriction in suction line
4. Low water level in pool
NOTE: If the recommendations in the Trouble
Shooting portion of this manual do not solve your
particular problem(s), please contact your local dealer
for service.