Jacuzzi Countertop Lavatories - Manual (Page 2)

Detach the faucet from the shut-off valves by
unscrewing the compression nut at the joints
between the valves and the water supply
tubes.
If the connection is corroded you may need to
cut off the nut with a hacksaw. If there is no nut
or shut-off valve, use a tube cutter or hacksaw
to separate the faucet from the water supply
tubes.
Keep the basin and sponge handy for water
that remains in the pipe and faucet.
Your new lavatory is finished to an attractive
high gloss. It may also be heavy and difficult
to lift. To protect the finish and avoid possible
damage before and after installation, please
handle your lavatory with care. Place the
lavatory on a thick bed of newspapers when
working on it before installation. Also, line the
inside of your lavatory with newspapers until
the job is done.
NOTE: For self-rimming models follow
steps 4, 5, 6, 8, 9, 11, 12, 14, 15, and 16; for
models requiring a metal mounting frame (not
provided) use steps 4, 7, 8, 9, 10, 11, 12, 13,
14, 15, and 16.
4. Once you have completed your bath-
room countertop and determined the general
location of your new lavatory, you are ready to
cut the opening into which it will be placed.
If you are installing your countertop lavatory in
a new or remodeled bathroom, make sure
that you are in compliance with all local plumb-
ing codes.
Rough-in information is included with your
lavatory. This information will be helpful in
placing the lavatory, water supply piping, shut-
off valves, and drains in their proper positions.
REMOVING YOUR OLD
LAVATORY
1. Turn off the water supply. This is done by
closing the two shut-off valves located under
the lavatory.
If there are no shut-off valves leading to the
lavatory, you must turn off the water at the
main valve. This is usually located in the
basement, garage, or near the foundation on
the outside of the house. It may also be near
the water meter.
Check to be sure the water is off by turning on
the faucet where you are working until the
water stops flowing.
If you have shut off the main valves in a two-
story house or greater, you should open an-
other faucet on the same or lower level. Water
will then drain from the entire line. This will
help avoid spills. Be sure and close the fau-
cets before you turn on the main valve again.
READ INSTRUCTIONS FIRST
You can determine which tools and materi-
als are necessary by reading the complete
installation instructions and examining the
job you have to do. These are normally
needed:
sponge
basin or pail
tape measure
flat blade screwdriver
emery cloth
hammer
saber saw or keyhole saw
drill
adhesive sealant with rust inhibitor
(included)
a 3-foot piece of 2" x 4"
heavy wire or cord (see step 3)
cardboard, newspapers or a dropcloth
2. Disconnect the drain pipes. Take off as
many sections as possible between the lava-
tory and the wall or floor to facilitate removal.
Place a basin under work area to catch any
water that may still be in the drain.
3. Before removing anything else, check to
see how the lavatory is supported. If the pipes
in the wall are providing support for the lava-
tory, use care in removing the faucet connec-
tions. The lavatory may fall once the faucet is
disconnected, so have a helper hold it up
while you work.
Look under the lavatory to see if there are lugs
holding it to the countertop. Do not remove the
lugs until you have first braced the lavatory
against falling.
You may be able to shore it up with pieces of
lumber from below. Or you can rig the support
as shown in Figure 1. This support consists of
a strong wire or cord draped over a 2" x 4".
Drop the wire through the drain and tie it to a
block of wood. Twist the cord until the block of
wood is snug against the tailpiece and pro-
vides a sure support for the lavatory. You may
then unscrew the lugs and lower the lavatory
by carefully untwisting the block of wood.
BEFORE YOU BEGIN
TOOLS AND MATERIALS
INSTALLING YOUR NEW
LAVATORY
The materials listed below are optional.
They are only necessary if existing mate-
rials are unusable:
Two shut-off valves with 1/2" I.P.S. outlet,
optional (check house piping to determine
valve inlet dimension)
1/2" I.P.S. hot and cold water supply tubes
with compression nut and ferrule
Drain tail pipe, trap, and additional drain pipe
as required
CAUTION: HANDLE
WITH CARE
Figure 1
hacksaw
basin wrench
tube cutter
adjustable
wrench (10")
pipe wrench (12")
metal mounting frame with four screw clips
(for non-self rimming lavatories only) pro-
vided by others. Be sure to select a frame that
fits the dimensions of your lavatory