beautypg.com

JL Audio 1000/1v2 User Manual

Page 11

background image

20 | JL Audio - 1000/1

v2

Owner’s Manual

21

“my amplifier shuts off once in a while, usually at higher volumes”

Check your voltage source and grounding point. The power supply

of the 1000/1v2 will operate with charging system voltages
down to 10V. Shutdown problems at higher volume levels
can occur when the charging system voltage drops below
10V. These dips can be of very short duration making them
extremely difficult to detect with a common DC voltmeter.
To ensure proper voltage, inspect all wiring and termination
points. It may also be necessary to upgrade the ground
wire connecting the battery to the vehicle’s chassis and the
power wire connecting the alternator to the battery. Many
vehicles employ small (10 AWG - 6 AWG) wire to ground the
battery to the vehicle’s chassis and to connect the alternator to
the battery. To prevent voltage drops, these wires should be
upgraded to 4 AWG when installing amplifier systems with
main fuse ratings above 60A. Grounding problems are the

leading cause of misdiagnosed amplifier “failures.”

“my amplifier turns on, but there is no output”

Check the input signal using an AC voltmeter to measure the

voltage from the source unit while an appropriate test tone is
played through the source unit (disconnect the input cables
from the amplifier prior to this test). The frequency used
should be in the range that is to be amplified by the amplifier
(example: 50 Hz for a sub bass application or 1 kHz for a full
range / high-pass application). A steady, sufficient voltage
(between 200mV and 8.0-volts) should be present at the
output of the signal cables.

Check the output of the amplifier. Using the procedure explained in

the previous check item (after plugging the input cables back
into the amplifier) test for output at the speaker outputs of
the amplifier. Unless you enjoy test tones at high levels, it is
a good idea to remove the speaker wires from the amplifier
while doing this. Turn the volume up approximately half
way. 5V or more should be measured at the speaker outputs.
This output level can vary greatly between amplifiers but it
should not be in the millivolt range with the source unit at
half volume. If you are reading sufficient voltage, check your
speaker connections as explained below.

Check to ensure that the speaker wires are making a good

connection with the metal inside the terminal block. The
speaker wire connectors are designed to accept up to 8 AWG
wire. Make sure to strip the wire to allow for a sufficient
connection with the metal inside the terminal block.

“How do i properly set the input sensitivity on my amplifier”

Please refer to Appendix A (page 14) to set the input sensitivity for

maximum, low-distortion output.

“my amplifier doesn’t turn on”

Check the fuse, not just visually, but with a continuity meter. It is

possible for a fuse to have poor internal connections that
cannot be found by visual inspection. It is best to take the
fuse out of the holder for testing. If no problem is found with
the fuse, inspect the fuse-holder.

Check the integrity of the connections made to each of the

+12VDC”, “Ground”, and “Remote” terminals. Ensure
that no wire insulation is pinched by the terminal set screw
and that each connection is tight.

Check to make sure there is +12V at the “Remote” connection of the

amplifier. In some cases, the turn-on lead from the source unit
is insufficient to turn on multiple devices and the use of a relay
is required. To test for this problem, jump the “+12VDC” wire
to the “Remote” terminal to see if the amplifier turns on.


“i get a distorted / attenuated sound coming out of the speaker(s)”

Check the speaker wires for a possible short, either between the

positive and negative leads or between either speaker lead
and the vehicle’s chassis ground. If a short is present, you
will experience distorted and/or attenuated output. The
Low Ω” light will illuminate in this situation. It may be
helpful to disconnect the speaker wires from the amplifier
and use a different set of wires connected to a test speaker.

Check the nominal load impedance to verify that the amplifier

is driving a load between 1.5 - 4Ω. JL Audio monoblock
amplifiers have two “+” positive connections and two “–”
negative connections. This is to facilitate multiple speaker
wiring. The two positive and two negative connections are
connected in parallel inside the amplifier. Connecting two
speakers, each to one set of positive and negative terminals,
will result in a parallel speaker connection. In this case,
each of the two loads should have a nominal
impedance between 3 - 8Ω.

Check the input signal and input signal cables to make sure signal

is present at the “Amplifier Inputs” and the cables are not
pinched or loose. It may be helpful to try a different set of
cables and/or a different signal source to be sure.

“my amplifier’s output fluctuates when i tap on it or hit a bump”

Check the connections to the amplifier. Make sure that the

insulation for all wires has been stripped back far enough to
allow a good contact area inside the terminal block.

Check the input connectors to ensure that they all are making good

contact with the input jacks on the amplifier.

aPPendix e: trouble sHooting