iHome iP41 User Manual

Page 7

Using the iP41

Setting Clock
1. Set the

DST Switch located on the back of the unit to +1 to add one hour or to -1 to subtract an hour.

When set to +1 the DST icon will appear.

2. Press and hold the Clock Adj Button located on the back of the unit until the display flashes. Press the

Hour and/or

Minute Button to set the time. Hold the button for a few seconds to adjust rapidly. Remem-

ber to set the correct AM or PM. An icon below the time digits is the PM Indicator.

3. Press the

Clock Adj Button again (or no button within 10 seconds) to exit the clock setting mode.

Using the Alarm
Setting the Alarm
1. Press and hold the

Alarm Button until the alarm time flashes. Press the Hour and/or

Minute Button to

set the alarm time. Hold the button for a few seconds to adjust rapidly. Remember to set the correct AM or
PM.

2. The alarm will automatically arm after set alarm time and the alarm icon will stay on to indicate alarm is

armed.

3. Default alarm sound is iPhone/iPod but if no iPhone/iPod is docked or iPhone/iPod cannot play for some

reason or the playing sound level is too low, it will automatically switch to buzzer alarm.

Arming and Disarming Alarm (Turn Alarm Function On and Off)
1. Once alarm is armed, press the

Alarm Button to disarm it.

2. Press the button again to arm the alarm again.

Resetting the Alarm to Come on the Next Day
When the alarm is sounding, press the

Alarm Reset/Power Button to stop the alarm and reset it to come

on the following day at the same time.

Snooze
Press the

Snooze/Dimmer Button after the alarm sounds. The alarm will be silenced and come on again

about 9 minutes later. Snooze can be pressed several times during the 1 hour alarm cycle.

Sure Alarm
The iP41 has a sure alarm feature so if a backup battery is installed, the buzzer alarm will still sound in the
event of power failure.

Using the iP41

Charging your iPhone/iPod
Note: Please make sure you are using the correct inset for your iPhone/iPod (see Install iPhone/iPod Insert) and
that it is properly docked into the iP41. Failure to do so may damage your iPhone/iPod.
While your iPhone/iPod is docked in the unit and the unit is connected to AC power, it recharges (until fully
charged).

Listening to iPhone/iPod
1. Dock the already playing iPhone/iPod, the iP41 will automatically turn on and you will hear the music

playing from your iPhone/iPod. Note: If the volume is too low on the iPhone/iPod, iP41 may not detect
iPhone/iPod is in play mode. Press the

Power Button on the main unit once or

Play/Pause Button

to play it.

2. When the iPhone/iPod is docked and in standby mode, press the

Button on main unit to play it. The

iPod icon will appear on the display indicating iPod mode

3. Press the

Button to pause play; press again to resume it.

4. Press the

and

Button to adjust the system volume.

5. Press or Button on remote control to go to the next or previous track. Press and hold while track is

playing for high speed forward or reverse music search of the current track.

6. You can rotate the unit for viewing video, the iP41 display also will change to fit your view orientation too.
7. To turn off the unit, press the

Button on the main unit or remote control. Your iPhone/iPod will continue

charging while in the dock.

Listening to non-docking iPod or other portable audio devices
If you are using an iPod without a docking port or other MP3 player or other portable audio device, you can play
it through the iP41 via the Aux-in Jack.
1. Plug one end of an audio patch cord (available at www.ihome.com ) into the headphone or line-out jack

on your device and the other end of the patch cord into the

Aux-in Jack, located on the back of the unit.

2. Press the

Button to turn the iP41 on.

3. Press the

Button on the main unit or on the remote control to adjust the system volume. You may

need to adjust your device volume too.

4. To turn off the unit, press the

Button. Please remember to turn off your device, too.

Watching Videos (iPhone and iPod models with Horizontal Video Mode)
Make sure you have installed the correct cradle for your iPhone, iPod touch or nano 4G model.
1. Gently turn the unit with docked iPhone or iPod on its left side. The clock display will adjust to the new

orientation.

2. Select a video file on your iPhone/iPod and press play.
3. Press Play on the iP41 if needed to turn unit on.