36) keystone commands, 8) remote commands, 9) password lock commands – MITSUBISHI ELECTRIC WD510U User Manual
Page 3: 7) mute commands
3
6) Keystone commands
(Not executable in stand-by mode. Possible only to read during muting.)
The keystone commands are used for the keystone setting of this projector with the value. The value will vary
depending on the installation conditions, etc.)
ITEM
ASCII
HEX
VALUE
KEYSTONE(vertical)
KS
4Bh
53h
+20 - -15
+20 - -5 (for WD500U-ST)
How to set the value
Use the ASCII or HEX code as shown below to set the value.
ASCII
'+'
'–'
'0'
'1'
'2'
'3'
'4'
'5'
'6'
'7'
'8'
'9'
HEX
2Bh
2Dh
30h
31h
32h
33h
34h
35h
36h
37h
38h
39h
Sending commands
Status code from
Description
from the PC, etc.
the projector
30 30 72 35 34 0D
Command operating the same
'0' '0' 'r' '5' '4' '
'
as the MENU button
30 30 72 35 34 0D
Command receipt confirmation
'0' '0' 'r' '5' '4' '
'
(Command echo back)
[Example]
When displaying the MENU selection bar (Figures and symbols enclosed in quotation marks are ASCII
codes.):
Button's name on remote
ASCII
HEX
+ VOLUME
r06
72h
30h
36h
– VOLUME
r07
72h
30h
37h
KEYSTONE
r43
72h
34h
33h
MAGNIFY
r02
72h
30h
32h
AV MUTE
ra6
72h
61h
36h
▲
r53
72h
35h
33h
▼
r2b
72h
32h
62h
t
r4f
72h
34h
66h
s
r59
72h
35h
39h
MENU
r54
72h
35h
34h
ENTER
r10
72h
31h
30h
AUTO POSITION
r09
72h
30h
39h
FREEZE
ra4
72h
61h
34h
ASPECT
re2
72h
65h
32h
8) Remote commands
(Not executable in stand-by mode. When the remote commands are sent while the splash
screen is being displayed, the splash screen is only canceled.)
Some remote control operations can be achieved by the remote command codes. The remote commands have no data codes.
9) Password lock commands
The password lock commands control the password lock. The password lock enabling or disabling command is sent
with a 4 to 8-digit password comprised of any figures 1 to 4 added to the end of the data code. When the password
lock is enabled or disabled successfully, the projector sends a return command comprising the data code,
password, and “1” at the end. When enabling or disabling the password lock fails, it sends a return command with
“0” at the end. There is no reconfirmation of the password. The password input command is for enabling projection
of image when password lock has been set to DISPLAY INPUT. The password input command is sent with a 4 to 8-
digit password comprised of any figures 1 to 4 at the end.
ITEM
ASCII
HEX
VALUE
Password lock
PSLOCK
50h
53h
4Ch
4Fh
43h
4Bh
0**** (Disabling), 1**** (DISPLAY INPUT),
enabling/disabling
2**** (MENU ACCESS), 3**** (SPLASH ID SCREEN)
Password input
PASS
50h
41h
53h
53h
****
**** is a 4 to 8-digit password comprised of any figures 1 to 4.
7) Mute commands
(Not executable in stand-by mode. When the mute commands are sent while the splash screen
is being displayed, the splash screen is only canceled.)
The mute commands are used for the mute setting of this projector with the 0 (30h) and 1 (31h).
ITEM
ASCII
HEX
VALUE
MUTE
MUTE
4Dh
55h
54h
45h
0 (OFF), 1 (ON)