English – Metabo TS 250 User Manual
Page 23
23
ENGLISH
For rip and cross cuts in grown tim-
ber and particle board.
E
TCT Saw Blade
250 x 2.8/1.8 x 30, 60 ATB teeth, 2
pinholes
For rip and cross cuts in grown tim-
ber and particle board.
F
TCT Saw Blade
250 x 2.8/1.8 x 30, 80 ATB teeth, 2
pinholes
For rip and cross cuts in panels;
plastic, aluminium, copper extru-
sions and high-grade veneered
sheets.
G
TCT Saw Blade
250 x 2.8/2.0 x 30, 80 square/trap-
ezoidal teeth
5° negative rake, 2 pinholes
General purpose blade for plastics,
thin-walled aluminium-, copper-,
brass- and steel extrusions as well
as for panels, laminates and
veneered sheets.
A
Danger!
Repairs to electric tools must
be carried out by qualified electri-
cians only!
Electric tools in need of repair can be
sent to the service centre of your coun-
try. Refer to the spare parts list for the
address.
Please attach a description of the fault to
the electric tool.
The machine's packing can be 100%
recycled.
Worn out power tools and accessories
contain considerable amounts of valua-
ble raw and rubber materials, which can
be recycled.
These instructions are printed on paper
produced with elemental chlorine-free
bleaching process.
A
Danger!
Before carrying out any fault service
or maintenance work, always:
1.
switch machine OFF;
2.
unplug power cable;
3.
wait for saw blade to come to
standstill.
Check that all safety devices are
operational again after each fault
service.
Motor does not run
Undervoltage relay tripped by power fail-
ure:
x
Restart machine.
No mains voltage
x
Check cables, plug, outlet and
mains fuse.
Motor overheated, e.g. by a blunt saw
blade or chip build-up in the chip case:
x
Remove cause for overheating, let
cool off for a few minutes. Then
press Reset button and restart
machine.
Stated top speed is not reached
Motor supply voltage too low:
x
use a shorter extension cable or
extension cable with larger lead
cross section (
t 1.5 mm
2
).
x
Have power supply checked by a
qualified electrician.
Loss of cutting performance
Saw blade blunt (possibly tempering
marks on blade body):
x
Replace saw blade (see chapter
“Maintenance”).
Dust spout blocked
No dust collector connected or suction
capacity insufficient:
x
connect dust collector, or
x
increase suction capacity (air speed
t 20 m/sec at chip ejection tube).
12. Repairs
13. Environmental Protection
14. Trouble Shooting
15. Technical specifications
Voltage
V
230 (1
a 50 Hz)
110 V (1
a 50 Hz)
Wattage
power input P1
power output P
2
kW
kW
2.0 kW S6 40%
1.2 kW S6 40%
1.55 kW S6 40%
0.84 kW S6 40%
Current draw
A
9.6
15.5
Fuse protection min.
A
16 (time-lag)
–
Protection class
IP 20
IP 20
Rated no-load speed (at 230V)
min
-1
3950
3900
Cutting speed (at 230V)
m/s
51.7
50.1
Saw blade diameter (outer)
mm
250
250
Saw blade arbor bore diameter (inner)
mm
30
30
Kerf width
mm
2.8
2.8
Depth of cut
with saw blade vertical
at 45° saw blade tilt
mm
mm
0 ... 77
0 ... 51
0 ... 77
0 ... 51
Dimensions
length of saw table
width of saw table
height (with blade guard)
mm
mm
mm
645
755 (985)
430
645
755 (985)
430
Machine weight
kg
32
32
Noise emission values, sawing,
A-sound pressure level L
pA
A-sound power level
LWA
dB (A)
dB (A)
83.6
97.9
83.6
97.9