Mb100 block diagram – Motorola MB100 User Manual
Page 4
Specification Notes:
1. Operating passband of station. Diplex filters are plugged into the electronic chassis.
2.
Referenced to the average gain across the stated passband.
3.
Minimum full gain at 1003 MHz includes loss of equalizer but Bode slope reserves have not been set. Return gain includes loss of SRE-*-4 return equalizer.
4.
Operational gain includes loss of slope reserves as well as equalizer.
5.
Amount of Bode slope control range from midpoint (typical setting is -4 dB at 1003 MHz @ 20°C). This control should not be used for gain reduction.
6.
Amount of slope created and cable equivalence of fixed interstage equalizer. Interstage equalizer is a plug-in.
7.
Noise Figure is specified at the cable entry facility of the housing and includes the loss of 1 dB for the pre-stage equalizer. The return Noise Figure includes the station loss preceding the RF
hybrid.
8.
Frequencies that relate the picture carriers or passband edges to the specified output levels and tilts.
9.
Measured with CW carriers and spectrum analyzer over specified temperature range. References the worst-case channel. Specifications are compliant with the test methods as stated in NCTA
RECOMMENDED PRACTICES FOR MEASUREMENTS ON CABLE TELEVISION SYSTEMS.
10.
Measured with wave analyzer and synchronous, 100% depth modulated channels. References the worst-case channels over specified temperature range. Specifications are compliant with the
test methods as stated in NCTA RECOMMENDED PRACTICES FOR MEASUREMENTS ON CABLE TELEVISION SYSTEMS.
11.
Composite Second Order distortion refers only to those beat clusters that fall +0.75 MHz and +1.25 MHz above the subject picture carrier. CSO beat clusters that have a -0.75 MHz and -1.25
MHz relationship to the subject picture carrier are not included in this specification.
12.
Test points should be used with GFAL adaptor.
13.
Match measurement at the station input and output, cable-entry facilities, at the specified passbands for operational gain.
14.
Measured with the stated AC Bypass Current.
15.
Measured at the power connector.
16.
Current draw at +24.0 VDC.
17.
AC current is stated in RMS continuous. A 10-amp compatible electronics package is also available for installing into older 10-amp housings during upgrades.
18.
Group Delay is specified for standard NTSC video, where delay is the delta from picture carrier to 3.58 MHz color subcarrier. Reverse delay is in a 1.5 MHz bandwidth.
19.
Hum Modulation performance is stated typical. Return band specified from 15 MHz. Hum Modulation (5 MHz to 15 MHz) is –55 dBc.
20.
Distortion numbers are worst case over temperature in a cascade.
21.
The compressed data loading is QAM carriers and are –6 dB relative to the analog CW carriers.
22.
CTB (Composite Triple Beat). At the specified channel loading, Enhanced Gallium Arsenide performance varies on a two point three-for-one (2.3:1) basis with amplifier output level.
MB100 Block Diagram
Motorola, Inc.
Connected Home Solutions
101 Tournament Drive
Horsham, PA 19044
1.800.523.6678
www.motorola.com/broadband
08.16.06
Rev 4.0
MOTOROLA and the Stylized M Logo are registered in the US Patent & Trademark Office.
All other product or service names are the property of their respective owners.
©
Motorola, Inc. 2003
Specifications are subject to change without notice.
4
Input
port 1
Port
2
Port
4
Port
3
DC
SP
JMP
RF/
AC
RF/
AC
RF
RF
AC
AC
TP
TP
TP
(Status
Monitor
Output)
TP
TP
TP
H
L
**
**
**
**
JXP-B
JXP-B
JXP-B
**
**
**
**
**
**
**
**
**
SRE
JXP-B
THERM
**
**
JXP
ICS
JXP
ICS
Fu
se
**
**
Fu
se
Fu
se
Fu
se
Power
supply
Plug-in
module
24 Vdc
**
**
JXP-B
Manual
Auto
ADU/
TDU
RF/AC
RF
AC
DC/
SP/
JMP
RF/
AC
RF
AC
To status
monitor
**
H
L
-1.0dB
-1.0dB
**
**
JXP-B
BODE
-6.5 dB
**
MDR
-1.0 dB
-4.0 dB
-4.0 dB
H
L
**
-1.0dB
-1.0dB
-1.7 dB F
-1.0 dB R
-20 dB
-20 dB
-20 dB
-20 dB
-20 dB
-20 dB
-1.7 dB F
-1.0dB R
-2.0 dB F
-1.0dB
-1.0dB
**
-1.0dB
SFE
or
SCS
PD
PD
+23 dB
PP
-1.0 dB R
-0.4dB
-0.5dB
Status
Monitor
Input
**
JXP-B
-16 dB
+30.0 dB -0.3dB
-4.0 dB
-4.0 dB
-0.4dB
-0.4dB
+20 dB
+20 dB
JXP-B
JXP-B
OnBrd
Atten
LPF
-0.4 dB
PP
+24 dB
RC
Therm
Cntrl
HPF
~ -7.0 dB
4 dB
tilt