Meyer Sound PSW-6 - Manual (Page 4)

T r a n s d u c e r s
A m p l i f i e r s
A u d i o I n p u t
A C P o w e r
P h y s i c a l
N o t e s
PHYSICAL DIMENSIONS
PSW-6 SPECIFICATIONS (cont’d)
Low Frequency
Type
Output Power
THD, IM, TIM
Type
Connector
Nominal Input Level
Connector
Automatic voltage selection
Opearional Voltage Range
Max Continuous RMS Current ( > 10 s)
Max Burst RMS Current (<1 s)
Max Peak Current During Burst
Soft Start Turn-on
Dimensions
Weight
Enclosure/Finish
Rigging
Two 18” diameter 8Ω MS-818 cone drivers
Four 15” diameter 4Ω MS-415 cone drivers
Complementary power MOSFET output stages, class AB/H
2480 Watts (620 Watts / channel)4
< .02 %
5 kΩ impedance, electronically balanced
XLR (A-3) male and female
+4 dBu (1.23 Vrms)
250V NEMA L6-20 (twistlock) inlet or IEC 309 male inlet
85 – 134 VAC and 165-264 VAC; 50 Hz / 60 Hz
Turn on: 85 VAC; Turn off: 134 VAC; 50/60 Hz
Turn on: 165 VAC; Turn off: 264 VAC; 50/60 Hz
115 V: 14 Arms
230 V: 7 Arms 100 V: 16 Arms
115 V: 26 Arms 230 V: 13 Arms 100 V: 30 Arms
115 V: 36 Apk 230 V: 18 Apk 100 V: 42 Apk
Inrush current <12 A @115 V
Height: 42.75”; Width: 42.52”; Length: 22.4”; Depth: 32.28”
442 lb (201 kg)
12-ply hardwood/black textured
Twelve pivoting lift rings (6 on top and bottom); working load for
each ring is 1500 lb with straight tensile pull. Safety factor is 5:1.
Entire cabinet is reinforced with steel girders
4. Nominal 8Ω resistive load, pink noise, 100V Peak.
ALL UNITS IN INCHES
Meyer Sound Laboratories, Inc.
2832 San Pablo Avenue
Berkeley, CA 94702
tel: 510.486.1166
fax: 510.486.8356
e-mail: [email protected]
http://www.meyersound.com
Meyer Sound Laboratories
has devoted itself to
designing, manufacturing,
and refining components
that deliver superb sonic
reproduction. Every part of
every component is
designed and built to
exacting specifications
and undergoes rigorous,
comprehensive testing
in the laboratories.
Research remains an
integral, driving force
behind all production.
Meyer strives for sound
quality that is predictable
and neutral over an
extended lifetime and
across an extended range.
Made by Meyer Sound, Berkeley, CA, USA
European Office:
Meyer Sound Germany
GmbH
Carl Zeiss Strasse 13
56751 Polch, Germany
© 1998 Meyer Sound Laboratories, Inc.
All rights reserved
3.1
26.9
14.0
32.3
29.4 Ref
C.G.
12.5
24.2
32.2
7.4
Top
1.6
(Rigging Typical, both ends)
Specifications subject to
change without notice
PSW-6 - 04.073.011.01
42.62
42.75 f
Front
(Without Grille Frame)
31.25
17.25
21.75
C.G.
Side
Rear
(Without Grille Frames)
ATENCI N: ACCESO INTERNO SOLO
AUTORIZADO A PERSONAL T CNICO CALIFICADO ACHTUNG: GEH USE NICHT FFNEN WARTUNG
UND REPARATUR NUR DURCH ELEKTROFACHKR FTE ATTENTION: ENTRETIEN ET REPARATIONS
INTERNES NE SONT AUTORISEES QU’AU PERSONNEL TECHNIQUE QUALIFI UK WARNING: THIS APPARATUS MUST BE EARTHED. NO OPERATOR SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED PERSONNEL
WARNINGS: THIS PRODUCT MUST BE GROUNDED
This surface may reach high temperatures while in use. To ensure proper operation, allow at least 6 inches clearance from this surface and adequate ventilation. To reduce the risk of electric shock do not remove cover. No operator serviceable parts inside. Refer servicing to qualified personnel. To reduce the risk of fire or electric shock do not expose this appliance to rain or moisture.
!
Meyer Sound, Berkeley, CA. USA 1 2 3 1 3 2 Loop Input
PUSH Active / Speaker Fault 2 + 3 + 10K Ω Balanced Input Polarity Front Exc Rear TPL Front TPL Rear Exc
Network S er vi ce W in k R es et A ct iv it y R e m o t e M o n i t o r i n g S y s t e m
PSW-6
Earth / Chassis 1 Case 220K Ω ESD
PU SH R E - C IR K- IT PU SH R E - C IR K- IT
95-125V ~ 50-60Hz
1400W RMS MAX 208-235V ~ 50-60Hz
1400W RMS MAX Auto-Voltage Select
U U
L L
C C
U U
L L
® ®
LISTED
3K59
COMMERCIAL
AUDIO SYSTEM