Motorola H680 - Manual (Page 2)

Power
Switch
Indicator
Light
IMPORTANT:
Be sure to first follow the
Quick Start Guide
on the reverse side
of this guide
to complete initial setup
of your H680.
Features and
Functions Guide
TURNING HEADSET ON
AND OFF
EARBUDS AND YOUR
HEADSET
Your H680 headset is supplied with multiple
earbuds. The earbud is fitted onto the end of
your headset’s earpiece speaker, and placed
onto your ear when using your headset.
Your headset’s performance is greatly
dependent upon achieving a good fit on your
ear. Therefore, we recommend trying all the
supplied earbuds with your headset.
• The essential requirements and
other relevant provisions of Directive
1999/5/EC.
• All other relevant EU Directives.
European Union Directives Conformance
Statement
Product
Approval
Number
The above gives an example of a typical Product
Approval Number.
You can view your product’s Declaration of Conformity
(DoC) to Directive 1999/5/EC (to R&TTE Directive) at
www.motorola.com/rtte. To find your DoC, enter the
product Approval Number from your product’s label in
the “Search” bar on the web site.
Hereby, Motorola declares that
this product is in compliance with:
To turn your headset on, slide the Power
switch on (towards Power symbol on
headset). The indicator light is steadily
purple for several seconds, then flashes
blue (if paired and connected with another
device) or is steadily blue (if ready to be
paired).
To turn your headset off, slide the Power
switch off. The indicator light will turn off.
WEARING THE
HEADSET
To wear your headset, flex the earhook and
loop it over your ear as shown.
Be sure to position the ear bud into your ear
canal for optimal audio performance and
comfort.
CHANGING FOR USE
ON OTHER EAR
Gently lift and pull the
top of the earhook up
and off speaker stem as
shown.
Flip the headset over.
Attach the earhook to
the speaker stem as
shown.
1
2
3
You can wear your H680 headset on your left or
right ear. The headset comes ready for the right
ear. To change the headset for the left ear:
MAKING CALLS MAKING CALLS
CONTINUED
Note: Your H680 supports both Handsfree and Headset
Profiles. Accessing call functions depends upon which
profile your phone supports. See your phone's user's guide
for more information.
Function Action
Receive a call Tap the Call button
Mute or unmute a call Tap both Volume
buttons
Reject a call Press and hold a
Volume button until
you hear two
descending tones
End a call Tap the Call button
Redial last call Press and hold the
Call button until you
hear two ascending
tones
Make a voice dial call Tap the Call button
and speak the
name after the tone
Function Action
Answer a second Tap the Call button
incoming call
Disable the
First slide the switch
indicator light toward charging plug
(to turn headset off),
then press and hold
both Volume
buttons AND slide
the switch towards
the microphone (to
turn headset on)
Note: Some features are phone/network dependent.
INDICATOR LIGHTS
With the Charger Plugged In
Headset Indicator Headset Status
Steady red Charging
Off Charging complete
With No Charger Plugged In
Headset Indicator Headset Status
Off Power off
Steady purple Powering up
Steady blue Pairing/connection
mode
10 rapid purple flashes Connection successful
Slow blue flash
Standby (not on call)
Quick blue flash Incoming call
Slow blue pulse Connected (on a call)
Slow purple pulse Connected
(on a muted call)
Red flash Idle (not connected)
Quick red flash Low battery
Note: After 30 minutes of inactivity, the light stops flashing to
conserve power, but the headset remains in standby mode.
AUDIO TONES
Audio Tone Headset Status
Ring tone Incoming call
Single high tone Phone network not
available
High to low tone End call
Single high tone when Volume at minimum
pressing volume button or maximum
Two ascending tones Mute enabled
Two descending tones Mute disabled
Low to high tone Connection
confirmation/voice
activation
No audio indications; Out of range
deteriorating quality
Two tones
Low battery
repeated every 30 sec.
STORING YOUR
HEADSET
The charger case provided is used to charge
and store your headset. When not using your
headset, you should place it in the charger
base. Be sure to turn the headset off before
placing it into the charger case.
As shown, the charger cover can be placed on
top of the charger case, or underneath it to
provide support for desktop placement.