MTD 6FE - Manual (Page 25)

25
Sales E & F
REF.
NO.
PART
NO. DESCRIPTION
1 731-2643 Clean Out Tool
2 684-04057 Impeller Assembly, 12” Diameter
3 710-0347 Hex Screw, 3/8-16, 1.75, Gr5, Std
4 710-0451 Bolt, Carriage, 5/16-18, .750 Gr1
5 710-0703 Screw, Carriage, 1/4-20, .75, Gr5
6 710-0726 Screw, Self-tapping, 5/16-12, 0.750
7 712-04063 Nut, Flange Lock, 5/16-18, Grf, Nylon
8 712-04064 Nut, Flange Lock, 1/4-20, Grf, Nylon
9 712-04065 Nut, Flange Lock, 3/8-16, Grf, Nylon
10 714-0149B Internal Cotter Pin
11 725-0157 Cable, Tie, 3/16 x .05 x 7.4
12 726-04012 Nut, Push-on, .25 Diameter
13 731-04705 Chute, Adapter 5” Diameter
14 732-0611 Spring, Extension, .38 OD x 3.6
15 736-0174 Washer, Wave, .625 x.885 x.015
16 731-2635 Mount, Clean Out Tool
17 738-0143 Screw, Shoulder, .498 x .340, 3/8-16
18 738-0281 Screw, Shoulder, .625 x .170, 3/8-16
19 738-04124 Pin, Shear, .25 x 1.50, Gr2
20 741-0245 Bearing, Hex Flange x .75 ID
21 741-0309 Bearing, Ball, .75 ID x 1.85 OD
22 756-0981A Idler Pulley, Flat 2.75 OD
23 790-00075 Housing, Bearing, 1.85 ID
24 790-00080 Bracket, Auger Idler w/ Brake
25 618-04170 Gearbox Assembly, Auger, 22”
618-04171 Gearbox Assembly, Auger, 24”
618-04172 Gearbox Assembly, Auger, 26”
618-04173 Gearbox Assembly, Auger, 28”
618-04165 Gearbox Assembly, Auger, 30”
26 684-04067 Housing Assembly, Auger 22”
684-04069 Housing Assembly, Auger 24”
684-04071 Housing Assembly, Auger 26”
684-04073 Housing Assembly, Auger 28”
684-04063 Housing Assembly, Auger 30”
27 684-04107 Spiral Assembly, LH
28 684-04108 Spiral Assembly, RH
29 714-04040 Cotter Pin, Bow-Tie
30 731-04870* Spacer, 1.25 OD x .75 ID x 1.00
31 736-0188 Washer, Flat, .76 x 1.49 x .06
32 738-04124 Shear Pin, .25 x 1.50, Gr2
33 741-0493A Bushing, Flange, .800 ID x .910 OD
34 790-00087 Housing, Bearing, 1” Hex
35 790-00117 Plate, Shave, 2.25 x 21.66
790-00120 Plate, Shave, 2.25 x 23.66
790-00121 Plate, Shave, 2.25 x 25.66
790-00118 Plate, Shave, 2.25 x 27.66
790-00119 Plate, Shave, 2.25 x 29.66
36 710-04071 Bolt, Carriage, 5/16-18, 1.0
37 720-04032 Knob Assembly
38 731-04426A Chute, Upper, w/ Domestic Label
39 731-04869 Chute, Keeper Flange
40 731-04912 Chute, Lower, 5.0 Diameter
41 736-0159 Washer.349 ID x .879 OD x .063
42 741-0475 Bushing, Plastic, .380
43 784-5647 Bracket, Chute Crank
44 784-5580 Shoe, Slide
45 719-0319 Housing, Auger, RH Reduced
46 719-0320 Housing, Auger, LH Reduced
47 721-0179 Seal, Oil, .750 ID
48 741-0662 Bearing, Flange, .75 ID x 1.00 OD x .59
49 710-0642 Screw, Self-tapping, 1/4-20, 0.750
50 711-04286 Axle, Auger, 22"
711-04285 Axle, Auger, 24"
711-04284 Axle, Auger, 26"
711-04283 Axle, Auger, 28"
711-04282 Axle, Auger, 30"
51 714-0161 Key, Hi-pro 3/16 x 5/8
52 715-04021 Pin, Dowel, .25 OD x 1.2
53 717-04126 Shaft, Worm .75 OD
54 717-0528A Gear, Worm 20T
55 718-04071 Collar, Thrust
56 721-0325 Plug, 1/4 x .437
57 721-0327 Seal, Oil, .75 x 1 x .131
58 736-0351 Washer, Flat, .760 ID x 1.5 OD
59 736-3084 Washer, Flat, .51 x 1.12
60 741-0663 Bearing, Flange, .75 ID x 1.00 OD x .925
61 746-0897 Auger Clutch Cable, 44.75”
62 741-0661A Bearing, Flange, .75 ID x 1.00 OD x .975
63 710-0276 Bolt, Carriage, 5/16-18, 1.0 Gr1
REF.
NO.
PART
NO. DESCRIPTION
* None found between spirals on models with 22-inch auger housing.
* One found between spirals on models with 24-inch auger housing.
* Two found between spirals on models with 26-inch auger housing.
* Three found between spirals on models with 28-inch auger housing.
NOTE:
Snow thrower features and components vary by model. NOT all parts listed above and pictured on the previous page
are standard equipment.