MITSUBISHI ELECTRIC XL1U - Manual (Page 17)

EN – 17
ENGLISH
CLAMP POSITION
SIGNAL-USER
0
CLAMP WIDTH 0
HORIZ. PIXELS 0
SHUTTER(RS) 0
VERT. LINES 0
VERT. SYNC. AUTO
SHUTTER(LS) 0
SHUTTER(L) 0
SHUTTER(U) 0
MEMORY CALL
SIGNAL
AUTO
HORIZ. POSITION 0
VERT. POSITION 0
TRACKING 0
COMPUTER INPUT RGB
FINE SYNC. 0
HOLD AUTO
USER MEMORIZE DELETE DEFAULT
R G B R G B
A
U
XGA60
opt.
VIDEO SIGNAL ... When AUTO is selected, the appropriate video format is automatically selected depending on the
input signal. If the image isn’t displayed correctly, select the desired video format manually.
ANAMORPHIC .... Select ON when playing DVD discs containing data of letterboxed images.
LANGUAGE ........ Use to select the language used in the menus. (
/ English / Español / Deutsch / Français /
Italiano / )
RESET ALL ......... Use to reset the MENU settings (except LANGUAGE).
4 SIGNAL
MEMORY CALL ........ Use to select AUTO, USER 1 or USER 2. See below.
HORIZ. POSITION .... Use to adjust the horizontal position of the image.
VERT. POSITION ..... Use to adjust the vertical position of the image.
FINE SYNC. ....... Use to synchronize the projector with PC input signals so
that the image is not blurred.
TRACKING ......... Use to avoid image noise such as wide stripes.
COMPUTER INPUT .... The unit adjusts itself automatically when connected to a
DVD player with a component video output (Y, C
B,
C
R
). In
the case ( Y, P
B,
P
R
). In the case the projector is connected to
equipment that includes RGB output terminal, adjust to
RGB mode.
HOLD .................. Adjusts the image when flagging occurs near the top of the
screen.
5 SIGNAL - USER (Normally, there is no need for adjustments.)
CLAMP POSITION/
CLAMP WIDTH ......... If you use something similar, the brighter colors of the
projected image may become blurred. In this case, adjust
CLAMP POSITION or CLAMP WIDTH.
HORIZ.PIXELS .. Use to adjust the width of the image. The image size grows
wider as the number increases. (Adjust to the horizontal
pixels of the input signal for normal setting.)
VERT.LINES ...... Use to adjust the height of the image. The image size grows
higher as the number increases. (Adjust to the vertical lines
of the input signal for normal setting.)
VERT.SYNC. ...... Use to adjust the image when its motion does not run
smoothly. Select AUTO for normal setting.
SHUTTER(U) ..... Use to adjust the image when the noise etc. appears on top part
of image.
SHUTTER(L) ...... Use to adjust the image when the noise etc. appears on bottom part of image.
SHUTTER(LS) .... Use to adjust the image when the noise etc. appears on left side of image.
SHUTTER(RS) ... Use to adjust the image when the noise etc. appears on right side of image.
User memory for signal setting
This projector can memorize the maximum of 2 signal menu settings.
Memorizing the setting
1. Select MEMORIZE in the SIGNAL menu, and press the ENTER button.
2. Press the
$ or % button to select the memory which you wish to record (USER 1 or USER 2).
3. Press the ENTER button.
• Any buttons are ineffective about 3 seconds of recording setting. Wait for recording to have been completed
before operating the buttons.
Initialite the setting which has been changed (Default)
Select RESET in the SIGNAL menu, and press the ENTER button.
Select the user setting
Select MEMORY CALL in SIGNAL menu, and press the
$ or % button to select the memory (USER 1 or USER 2).
Reset the recorded setting
1. Select DELETE in the SIGNAL menu, and press the ENTER button.
2. Press the
$ or % button to select the memory which you wish to reset (USER 1 or USER 2).
3. Press the ENTER button.
The recorded setting will be reset.
• Any buttons are ineffective about 3 seconds of resetting the recorded setting. Wait for resetting to have been
completed before operating the buttons.