Musical Fidelity X-P200 - Manual (Page 2)

IMPORTANT! (U.K. only)
This unit is supplied in the U.K. with a mains lead fitted with a moulded 13 amp plug.
If, for any reason, you need to cut off this plug, please remove the fuse holder and dispose of
the plug safely, out of reach of children. It must not be plugged into a mains outlet.
The wires in the mains lead supplied with this appliance are coloured in accordance with
the following code:
Green and yellow..............Earth
Blue...............................Neutral
Brown................................Live
WARNING - This appliance must be earthed
As the colours of the wires of the mains lead of this appliance may not correspond with the
coloured markings identifying the terminals in your plug, proceed as follows:
The wire which is coloured green-and-yellow must be connected to the terminal in the plug
which is marked with the letter E or coloured green or green-and-yellow, or by the earth
symbol:
The wire which is coloured brown must be connected to the terminal which is marked with
the letter L or coloured red.
The wire which is coloured blue must be connected to the terminal which is marked with the
letter N or coloured black.
If connecting to a BS1363 plug, a 13 amp fuse must be used.
SAFETY INFORMATION
X-P200 Power Amplifier Page 7 of 7 Page 2 of 7 X-P200 Power Amplifier
WARNING:
Any modifications to this product not expressly approved by Musical Fidelity who
is the party responsible for standards compliance could void the user’s authority to
operate this equipment.
Your new X-P200 is designed and built to provide trouble-free performance, but as with all
electronic devices, it is necessary to observe a few precautions :
„ Do not use the X-P200 near water. The unit must not be exposed to dripping or splash
ing and no objects filled with liquids, such as vases, must be placed on the unit.
„ Keep the X-P200 away from heat such as radiators. No naked flame sources, such as
lighted candles, should be placed on the unit.
„ Place all connecting cables where they are not likely to be walked on or trapped by items
placed on them.
Output :
Power, stereo mode : 125 Watts, one channel loaded into 8 Ohms
(21dBW)
Power, bridge mode : 260 Watts into 8 Ohms (24dBW)
Voltage RMS, stereo mode : 31.6 Volts 20Hz to 20kHz, one channel loaded
Voltage peak, stereo mode : 44.5 Volts, one channel loaded
Current peak-to-peak (unlimited) : 75 Amps
Damping factor, stereo mode : 200
Output devices per channel : 4 (stereo), 8 (bridge)
Line inputs :
Total harmonic distortion + noise : < 0.015 20Hz to 20kHz
Signal / noise ratio : > 107dB ‘A’-weighted
Input sensitivity for 125W, 8 Ohms : 1 Volt
Input impedance : 27k Ohms in stereo mode, 220k Ohms bridge mode
Channel separation : > 70dB typical
Frequency response : 20Hz to 20kHz, + 0, - 0.1dB
Input facilities : “A” 1 pair RCA connectors, selectable from front panel
“B” 1 pair RCA connectors, selectable from front panel
Output facilities : 2 amplifier channels or 1 channel in bridge mode
(switchable from front panel) via 1 pair per channel
binding posts.
1 pair RCA loop output sockets
Power requirement : 100 / 115 / 230Volts AC 50 / 60Hz (factory pre-set),
600 Watts maximum (bridge mode) into 8 Ohms,
30 Watts idle.
Dimensions : 218mm, 8.6 inches wide
98mm, 3.8 inches high (including feet)
339mm, 13.4 inches deep (including knob
and rear terminals)
Weight : 6.1 kg, 13.4 lbs unit only, unboxed
7.15 kg, 15.8 lbs in shipping carton
Standard accessories : IEC type mains lead (10-Amp type)
Musical Fidelity reserves the right to make improvements which may result in specification
or feature changes without notice.
X-P200 SPECIFICATIONS