Control panel decals – Multiquip Stay-Level Handlebar Pavement Saw PS706026 User Manual

Page 10

PAGE 10 — PS7060 SERIES MULTIQUIP SAW — PARTS MANUAL — REV. #8 (07/26/10)

INCH

100

125

150

175

200

230

255

280

305

330

355

380

WATER PUMP

OFF

WATER

OFF

BRAKES:

This saw is equipped with parking brakes.

This saw is equipped with parking brakes.
Brakes are applied automatically when engine

Brakes are applied automatically when engine
is off and dis-engaged when engine is running.

is off and dis-engaged when engine is running.

BEFORE
STARTING:

WATER
SUPPLY:

BLADES:

STARTING
ENGINE:

STOPPING
ENGINE:

FWD-
NEUTRAL-

NEUTRAL-
REV
CONTROL:

RAISE-

RAISE-
LOWER
FUNCTION:

Check all fluid levels. Secure blade firmly to

Check all fluid levels. Secure blade firmly to
bladeshaft. Make sure all protective guards

bladeshaft. Make sure all protective guards
are in place and properly mounted. Wear eye,

are in place and properly mounted. Wear eye,
ear protection and protective clothing.

ear protection and protective clothing.

Connect water supply to water inlet. Move

Connect water supply to water inlet. Move
water ON/OFF CONTROL to ON position.

water ON/OFF CONTROL to ON position.
Adjust WATER FLOW CONTROL lever to

Adjust WATER FLOW CONTROL lever to
desired position. Drain watering system in

desired position. Drain watering system in
cold weather to prevent damage due to

cold weather to prevent damage due to
freezing.

freezing.

Always follow blade manufacturer's

Always follow blade manufacturer's
recommendations for blade selection,

recommendations for blade selection,
speed and application.

speed and application.
NEVER exceed blade manufacturer's

NEVER exceed blade manufacturer's
maximum rated RPM. See operator's manual

maximum rated RPM. See operator's manual
for detailed blade mounting instructions.

for detailed blade mounting instructions.

Set CONTROL HANDLE to NEUTRAL position.

Set CONTROL HANDLE to NEUTRAL position.
Set THROTTLE to IDLE. Turn start switch to

Set THROTTLE to IDLE. Turn start switch to
ON position. Wait for glow plug indicator light

ON position. Wait for glow plug indicator light
to go out. Momentarily turn switch to start

to go out. Momentarily turn switch to start
position; release switch as soon as engine

position; release switch as soon as engine
starts. Allow engine to warm up for several

starts. Allow engine to warm up for several
minutes before increasing engine speed. Use

minutes before increasing engine speed. Use
approved diesel fuel only.

approved diesel fuel only.

Do not stop engine abruptly when hot! Reduce

Do not stop engine abruptly when hot! Reduce
THROTTLE to IDLE and allow engine to run 1

THROTTLE to IDLE and allow engine to run 1
to 2 minutes before turning ignition switch off.

to 2 minutes before turning ignition switch off.
Damage to engine may occur if not allowed to

Damage to engine may occur if not allowed to
cool adequately.

cool adequately.

The panel mounted handle controls

The panel mounted handle controls
FORWARD, NEUTRAL and REVERSE

FORWARD, NEUTRAL and REVERSE
operation. Neutral position stops or holds saw

operation. Neutral position stops or holds saw
in a stationary position. Incremental

in a stationary position. Incremental
movement in the FORWARD or REVERSE

movement in the FORWARD or REVERSE
direction will increase speed proportionate

direction will increase speed proportionate
to amount of movement.

to amount of movement.

RAISE-LOWER function is controlled by the

RAISE-LOWER function is controlled by the
switch mounted at the right side of the

switch mounted at the right side of the
CONTROL HANDLE. Push toggle switch

CONTROL HANDLE. Push toggle switch
lever forward to lower saw. Pull toggle switch

lever forward to lower saw. Pull toggle switch
lever backward to raise saw.

lever backward to raise saw.

OPERATING INSTRUCTIONS

FORWARD

NEUTRAL

REVERSE

WARNING

BLADESHAFT ROTATION DIS-ENGAGEMENT SYSTEM

Engine must be at idle when engaging or

Engine must be at idle when engaging or
dis-engaging bladeshaft drive.

dis-engaging bladeshaft drive.

To stop bladeshaft rotation:

To stop bladeshaft rotation:
Push rocker switch labeled BLADESHAFT forward.

Push rocker switch labeled BLADESHAFT forward.
Engine will tilt forward, dis-engaging the belt drive.

Engine will tilt forward, dis-engaging the belt drive.

To start bladeshaft rotation:

To start bladeshaft rotation:
Push rocker switch labeled BLADESHAFT backward.

Push rocker switch labeled BLADESHAFT backward.
Engine will tilt back, engaging belt drive.

Engine will tilt back, engaging belt drive.

ENGINE MUST BE SHUT OFF

when removing or installing

blade or bladeguard or performing any type of service

blade or bladeguard or performing any type of service
to bladeshaft or any other component on machine!

to bladeshaft or any other component on machine!

NEVER

attempt to remove or install blade or bladeguard

with engine running by dis-engaging the belt drive!

NEVER

attempt to service any component with the

engine running!

NEVER

leave saw unattended while engine is running!

RAISE/LOWER

SWITCH

FWD-NEUTRAL-REV

CONTROL

NEVER EXCEED BLADE MANUFACTURER'S RECOMMENDED RPM'S

ADJUST WATER FLOW VALVE

ADJUST WATER FLOW VALVE
FOR DESIRED WATER FLOW

FOR DESIRED WATER FLOW

WATER

FLOW

CONTROL

TO ADJUST CUT DEPTH INDICATOR:

TO ADJUST CUT DEPTH INDICATOR:
LOWER SAW UNTIL BLADE CONTACTS

LOWER SAW UNTIL BLADE CONTACTS
SURFACE, ADJUST DIAL TO ZERO.

SURFACE, ADJUST DIAL TO ZERO.

DEPTH

INDICATOR

To Control Depth of Cut with Saw

To Control Depth of Cut with Saw
Running and Blade Mounted:

Running and Blade Mounted:

Step 1:

Raise saw above desired cutting depth.

Step 2:

Turn depth control knob counterclockwise

until saw cannot be lowered by pushing raise/lower

until saw cannot be lowered by pushing raise/lower
switch forward.

switch forward.
Step 3:

Step 3:

Hold raise/lower switch in the lowering

position and rotate the depth control knob clockwise

position and rotate the depth control knob clockwise
until desired cutting depth is achieved. The saw will

until desired cutting depth is achieved. The saw will
repeat to the same depth until re-adjusted.

repeat to the same depth until re-adjusted.

To Re-adjust for Full Cutting Depth:

Hold raise/lower switch in the lowering position and

Hold raise/lower switch in the lowering position and
rotate the depth control knob clockwise until saw is

rotate the depth control knob clockwise until saw is
fully lowered. Rotate depth control knob clockwise

fully lowered. Rotate depth control knob clockwise
additional 1 turn.

additional 1 turn.

DEPTH STOP CONTROL

MAINTENANCE INSTRUCTIONS

ENGINE

Air filter:

Replace outer element when the SYSTEMS

air filter restriction light comes on.

STATUS
Replace inner element every fourth outer element.

Oil:

Check oil level daily, do not overfill.

Oil type:

See Engine Manual.

Oil Service:

Change oil and filter every 125 hours
of operation.

Fuel Filter:

Change fuel filter every 250 hours of operation.

HYDRAULIC SYSTEM

Oil Level:

Check reservoir daily. Fill reservoir to
line marked FULL COLD.

Oil type:

15W-40 premium grade engine oil.

Oil Service:

Change oil and filter every 500 hours of
operation or annually, whichever occurs first.

Reservoir

Reservoir is located inside console. Remove

Location:

rear panel for access.

Wheel drive propulsion system, lift pump,
and oil bath bladeshaft share common
hydraulic oil reservoir, thus are maintained
as a single system.

LUBRICATION

Service:

Grease every 125 hrs. of operation.

Type:

Note:

Use premium grade waterproof
EP (extreme pressure) grease.

Locations: Front axle pivot bearings (2), lift

cylinder pins (2), engine tilt cylinder
pin (1).

DRIVE BELTS

Belt Tension:

Bladeshaft drive belt tension is applied hydraulically when
bladeshaft drive is engaged.

To Adjust

Perform following procedure with saw fully lowered.

Drive Belt

Loosen jam nut on belt tension limiting bolt. Turn belt tension limiting bolt
counterclockwise to create ½” minimum distance between end of bolt and frame.
Start engine and engage belt drive; increase engine speed to full throttle position for
15 seconds minimum. Slow engine speed to idle and shut engine off. Turn belt
tension limiting bolt clockwise until bolt lightly contacts frame. Tighten locknut.

Tension:

ENGINE WILL NOT CRANK
OR START WHEN E-STOP
BUTTON IS DEPRESSED

TACHOMETER

SYSTEMS STATUS

BLADE SPEED

ENGINE PRE-HEAT
GLOW PLUG

ENGINE
PRE-HEAT

START

OFF

IGNITION SWITCH

ENGAGE

OFF

BLADESHAFT

DIS-ENGAGE

LIGHTS

AUXILIARY

THROTTLE

TO INCREASE ENGINE SPEED: TURN KNOB COUNTERCLOCKWISE.
TO REDUCE ENGINE SPEED:

TURN KNOB CLOCKWISE.

FOR QUICK THROTTLE ACTION: DEPRESS RED BUTTON AND

PUSH OR PULL KNOB.

CONTROL PANEL DECALS

CONTROL PANEL DECALS

This manual is related to the following products:

Stay-Level Handlebar Pavement Saw PS706036 Stay-Level Handlebar Pavement Saw PS706020 Stay-Level Handlebar Pavement Saw PS706030 Stay-Level Handlebar Pavement Saw PS706016 PS706036 PS706030 PS706026 PS706020 PS706016