Maxim Manufacturing TP50B - Manual (Page 4)

Figure 1
Figure 2
bolts, nuts and lock washers. The left brace bolts between the belt guard bracket and the transmission.
The braces are mounted to the handle bars using one 1/4” - 20 x 1 1/2 and one 1/4” - 20 x 1 3/4” hex bolts,
nuts, and lock washers. The clutch cable guide mounts on the outside of the right handle bar. Route the
clutch cable through guide with the adjustment at the top. See Figure 1.
6. Install the handle bar cross brace between the handle bars using four 1/4” - 20 x 1 1/2” hex bolts, nuts,
and lock washers. See Figure 1.
7. Route the throttle control cable under the handle passing under the cross brace.
8. Tighten all bolts at this time.
9. Install clutch cable by hooking loop at bottom into notch in clutch arm. Hook spring into clevis and into
hole in clutch lever. The clutch cable should be adjusted so that the belt will slip when released and the
spring will be extended 1/4” when lever is engaged.
10. Install handle bar grips (Some type of lubricant such as liquid soap will be helpful).
FINAL SETUP
1. Check the transmission to that it is full. See Figure 3.
a. Remove check plug.
b. Use 90 wt. gear lube or 50 weight motor oil. Approximately 1 pint.
c. Fill until check plug overflows.
d. Replace plug.
2. Remove the engine dipstick and fill crankcase with oil ac-
cording to engine owner’s manual.
3. Fill fuel tank. Use clean, fresh, lead-free, gasoline. Fill
the tank completely.
DO NOT MIX OIL WITH GASOLINE.
right as you stand in an operating position. See Figure 1 and 2.
5. Install the two handle bar tie braces between the holes in the transmission and the lower holes in the
handle bars. Fasten the braces to the transmission using one 5/16” - 18 x 1” and one 5/16” x 1 1/4” hex
MT and TP Models RMT
Ref# Part # Quan. Description Part # Quan Description
101 336682 1 Main Frame Rail LH
102 336681 1 Main Frame Rail RH
103 359335 2 Frame Spacer
302 130695 1 Handle Bar LH 162081 1 Handle Bar Left Hand
303 336678 2 Handle Bar Brace
304 130730 1 Handle Cross Brace
305 313786 2 Handle Grip 4
308 130694 1 Handle Bar Right Hand 162082 1 Handle Bar RH Heavy Duty
402 162077 1 Intek Throttle Control
403 402014 2 #10 - 3/8” Slot Tapping Screw
404 336683 1 Clutch Lever
405 359345 1 Clutch Lever Pin
407 359346 1 Clutch Locking Pin
408 359359 1 Clutch Locking Spring
409 359327 1 Clutch Cable Spring
410 162041 1 Clutch Cable and Adjustment
413 359326 2 Clutch Cable Guide
414 359323 1 Throttle Cable Clip
601 162031 2 Wheel, 10” x 1.75 162065 2 Wheel, 10” x 1.75” Heavy Duty
605 461467 1 Wheel Yoke Locking Pin
606 359362 1 Lock Pin Spring
607 461468 1 Cotter Pin
609 162032 1 Wheel Yoke Assembly 162033 1 Wheel Yoke Assembly
615 130701 2 Hitch Casting
618 336686 1 Depth Bar
621 359363 1 Depth Bar Adjust. Spring
625 461469 1 Depth Bar Adjust. Pin
705 359321 1 Idler Pulley 338009 1 Idler Pulley
706 162069 1 Idler Shaft
708 359325 1 Idler Shaft Arm
709 400290 1 Capscrew NC, 3/8” x 1 3/4”
802 359330 2 Wheel Shoulder Bolt
804 400184 2 Cap Screw, NC 5/16” x 3/4”
805 400186 1 Cap Screw, NC 5/16” x 1” 400190 Cap Screw, NC 5/16” x 1 1/4”
806 400197 1 Cap Screw, NC 5/16” x 2 1/4”
807 400200 4 Cap Screw, NC 5/16” x 2 1/2”
809 400207 2 Cap Screw, NC 5/16” x 3 3/4”
811 400275 1 Cap Screw, NC 3/8” x 3”
813 400115 5 Cap Screw, NC 1/4” x 1 1/2”
814 400109 1 Cap Screw, NC 1/4” x 1 3/4”
816 443101 6 Nut, NC 1/4”
817 443106 11 Nut, 5/16”
818 443110 2 Nut NC, 3/8”
819 444721 4 Locknut NC, 3/8”
820 444720 1 Locknut NF, 3/8”
821 446130 6 Lockwasher, 1/4”
822 446136 11 Lockwasher, 5/16”
825 455050 1 Washer SAE Flat, 1/2”
830 162096 Optional LH Tine Shield
831 162095 Optional RH Tine Shield
833 359853 1 Engine Guard
4
SET UP INSTRUCTIONS CONTINUED
13