Greenway Home Products Electric Fireplace Mantel MEF2511OK - Manual (Page 3)

gET REady TO sTaRT
Before assembly, use scissors to unwrap the parts from the packaging. DO NOT use a box cutter or exacto-knife as
you may cut into the mantel pieces inside the box and damage the finish. Check for the hardware bag which is RED and
located inside the packaging, taped to the top box. Be sure you DO NOT discard any pieces.
step 1
Locate the base and place it on the floor. Do not put it up against
the wall at this point in the assembly, as you need to get in behind
the mantel to insert several wingnuts, lock washers and firebox screws.
step 2
Locate the left side panel and the left front panel. Facing the front of the base,
take the left side panel, positioning it so the holes in the blocks on the bottom
line up with the holes on the base. Position the left front panel next to the left side
panel, lining up the holes in the blocks with the holes on the base. Attach the left
front and side panel to the base by inserting and tightening 1 wingnut and 1 lock
washer to each piece. Attach the left side and front panels together by inserting
and tightening 3 wingnuts and 3 lock washers onto the blocks.
step 3
Repeat Step 2, but with the right side panel and the right front panel.
step 4
Locate the upper facing panel. Position the panel with the finished side facing the
front of the mantel. Attach to the right and left legs by lining up the holes on each
side inserting and tightening 1 wing nut and 1 lock washer on each side.
Locate the central header that will be attached to the left and right legs and will
sit above the upper facing panel. Position this panel with the finished side facing
the front of the mantel. Line up the holes on each side and insert and tighten 2
wingnuts and 2 lock washers on each side.
step 5
Get your assistant and locate the top of your mantel. This top is very heavy. It
will take 2 people to lift and position it in place. Ensure the top goes over the
positioning guide located on the header. The top must go over this guide to be
positioned correctly. Line up the holes on the top of the mantel, insert and tighten
5 wing nuts and lock washers.
381
118
1016
320
1
2
3
4
5
6
1
1
1
1
1
1
MEF2511OK MODEL
ITEM NAME
PART NO.
MANTEL
PART NAME QTY.
7 1 UPPER FACING
8 1
1143
638
471
1092
60
RIGHT SIDE PANEL
BASE
CENTRAL HEADER
RIGHT FRONT PANEL
LEFT SIDE PANEL
LEFT FRONT PANEL
TOP
RIGHT SIDE PANEL
BASE
CENTRAL HEADER RIGHT FRONT PANEL
LEFT SIDE PANEL
LEFT FRONT PANEL
TOP
2PC 2PC
4PCS
FLAT HEAD SCREW(4*30mm)4PCS
FLAT HEAD SCREW(4*16mm)4PCS
WING NUT(5*28) 23PCS
SPRING LOCK 23PCS
MEF2511OK
UPPER FACING
381
118
1016
320
1
2
3
4
5
6
1
1
1
1
1
1
MEF2511OK MODEL
ITEM NAME
PART NO.
MANTEL
PART NAME QTY.
7 1 UPPER FACING
8 1
1143
638
471
1092
60
RIGHT SIDE PANEL
BASE
CENTRAL HEADER
RIGHT FRONT PANEL
LEFT SIDE PANEL
LEFT FRONT PANEL
TOP
RIGHT SIDE PANEL
BASE
CENTRAL HEADER RIGHT FRONT PANEL
LEFT SIDE PANEL
LEFT FRONT PANEL
TOP
2PC 2PC
4PCS
FLAT HEAD SCREW(4*30mm)4PCS FLAT HEAD SCREW(4*16mm)4PCS
WING NUT(5*28) 23PCS
SPRING LOCK 23PCS
MEF2511OK
UPPER FACING
381
118
1016
320
1
2
3
4
5
6
1
1
1
1
1
1
MEF2511OK MODEL
ITEM NAME
PART NO.
MANTEL
PART NAME QTY.
7 1 UPPER FACING
8 1
1143
638
471
1092
60
RIGHT SIDE PANEL
BASE
CENTRAL HEADER
RIGHT FRONT PANEL
LEFT SIDE PANEL
LEFT FRONT PANEL
TOP
RIGHT SIDE PANEL
BASE
CENTRAL HEADER RIGHT FRONT PANEL
LEFT SIDE PANEL
LEFT FRONT PANEL
TOP
2PC 2PC
4PCS
FLAT HEAD SCREW(4*30mm)4PCS
FLAT HEAD SCREW(4*16mm)4PCS
WING NUT(5*28) 23PCS
SPRING LOCK 23PCS
MEF2511OK
UPPER FACING
Step 1
Step 4
Step 5
381
118
1016
320
1
2
3
4
5
6
1
1
1
1
1
1
MEF2511OK MODEL
ITEM NAME
PART NO.
MANTEL
PART NAME QTY.
7 1 UPPER FACING
8 1
1143
638
471
1092
60
RIGHT SIDE PANEL
BASE
CENTRAL HEADER
RIGHT FRONT PANEL
LEFT SIDE PANEL
LEFT FRONT PANEL
TOP
RIGHT SIDE PANEL
BASE
CENTRAL HEADER
RIGHT FRONT PANEL
LEFT SIDE PANEL
LEFT FRONT PANEL
TOP
2PC 2PC
4PCS
FLAT HEAD SCREW(4*30mm)4PCS FLAT HEAD SCREW(4*16mm)4PCS
WING NUT(5*28) 23PCS
SPRING LOCK 23PCS
MEF2511OK
UPPER FACING
Step 2 & 3
2