Graco 3835 - Manual (Page 3)

HARNESS MODELS:
Place the crotch strap between your child’s legs and
insert the harness buckles into the center buckle
housing. Adjust shoulder straps as needed (pull adjust-
ment buckles down to loosen harness, push them up
to tighten harness) to get a snug fit around your child.
Check that belt is tightly threaded through retainers
behind seat.
To release, squeeze buckle at right
and left sides of center housing.
The position of the shoulder straps can be adjusted
for the size of your child. Locate the small retainers
behind the seat back, push them through to the
front and move them to the higher or lower position
as needed.
If it becomes necessary to remove the seat belt, follow
these instructions:
SEAT BELT MODELS:
Step 1.
Unthread both ends of seat belt
through the buckles as shown.
Step 2.
Pull one end of the seat belt
through the belt retainer as
shown.
Step 3.
To rethread buckle, reverse the above steps. CHECK
that the belt is threaded correctly by pulling on the seat
belt. The belt should not slip through the buckle.
HARNESS MODELS:
Remove seat pad. Follow directions given under “To
Attach Seat Pad” to remove harness straps from seat.
SEAT PAD WITH POCKET:
Your highchair will have either a seat belt or a 5-point
harness. Follow the proper instructions below.
Step 1.
SEAT BELT MODELS:
Position seat pad over highchair.
Pull the seat belt through the
hole in the middle of the seat pad.
5-POINT HARNESS MODELS:
Straps must first be removed
from seat before pad can be
attached. Behind the seat back,
locate four small plastic retainers
on the shoulder straps. Push
them through the slots in seat
to the front. Set straps aside.
Position seat pad over highchair.
Push each plastic retainer through
proper hole in seat pad and back
into slot it was removed from, as
shown. (The strap length adjust-
ment buckles will be near the
shoulders.) Avoid twisting straps.
Two levels of shoulder holes are provided. Choose the
level that is at or slightly above your child’s shoulders.
Pull crotch strap and buckle through center opening in
seat pad.
Step 2.
Attach seat pad by sliding pocket
over the back of the seat as
shown.
NOTE: On certain models with a
cloth pad, pad is reversible. Turn
pocket inside out to reverse.
To Use Restraint
SEAT BELT MODELS:
Place crotch strap between
child’s legs and snap both side
buckles to the center buckle.
Adjust belt as needed to get a
snug fit around your child.
Push in on front of buckle to
release.
5 225-12-98 IS3850
Step 1.
IMPORTANT: BEFORE attaching feet to highchair,
frame MUST be folded exactly as in the drawing below.
Lay highchair frame on floor so it looks like the
drawing before attaching feet.
Place a foot top and foot bottom at each corner of the
chair frame tube. Insert a screw into the foot bottom,
through the hole in the chair frame, and into the foot
top. Tighten screws securely, but do not overtighten.
Step 2.
Unfold the chair frame
as shown. Insert one
bolt and one T-nut into
each leg brace and
through the holes in
the legs. Tighten them
securely with a screw-
driver and the enclosed
hex wrench.
Step 3.
Snap end caps into ends of
right and left plastic leg tubes.
Step 4.
Turn the seat upside down
as shown. Match up the
“L” or “R” on the plastic
leg tubes with the letters
molded on the seat back.
Slide the leg tubes into the
“collars” on the seat back.
Slide the crossbrace tube
through the slots under
the seat. Then insert the
ends of the crossbrace
tube into the holes in the
leg tubes. (This may be
more easily done if the
crossbrace tube is held at
an angle as shown.)
Step 5.
Set chair frame into upright
position. Slide the seat assem-
bly onto the frame. Press the
red latches, located on the
plastic leg tubes, to allow seat
to slide onto frame.
NOTE: Lowest seat position
should NOT rest on top of legs.
Pull seat up to lowest latching
position.
To Attach Seat Pad
SEAT PAD WITH FOUR TABS:
Step 1.
Place seat pad in seat. Large
part of pad goes on seat back
as shown. Pull the seat belt
through the hole in the middle
of the seat pad.
Step 2.
Push the four tabs on the seat
cover into the slots at the top
and bottom of the seat.
Step 3.
From the rear of the seat, pull
the four tabs over the plastic
anchors near them.
6 8 7
To Assemble Highchair
Hex wrench
Left
plastic
leg tube
Collars
Crossbrace
tube
Right
plastic
leg
tube
Lowest
latching
position
NOT
resting
on legs
Anchor
Seat
back
Seat
bottom
Your highchair seat pad will either have 4 attachment tabs
or a pocket on the back. Follow the appropriate instructions
below:
T-nuts
Slack
length
adjustment
buckle
Loosen
Tighten
Prevent serious
injury or death from falls or sliding
out. Always secure your child in
the restraint. Do not depend on the
tray alone to hold your child.