beautypg.com

Attaching the legs, Attaching the hanger, Adjusting the handle – Graco 1501 User Manual

Page 3: Using the carrier, Installing batteries, Starting the cradle, Using the tray, Adjusting the stand, Using the cradle

background image

Attaching the Legs

Step 1.

Push oval end of the upper leg

sections firmly onto the four

plastic pegs. Hold tube vertically

while pushing in. Push leg on

completely.

Step 2.

Push the leg tips on the round

ends of the lower leg sections.

(The other ends have a wire.)

Step 3.

Put the wire end of lower leg

sections into the round end of

the upper leg sections. Push

the sections together while

twisting lower leg slightly. This

will ensure a snug fit.

Step 4.

CHECK:

Lift swing as shown. If legs are

assembled properly, the legs

will dangle from the motor unit

and not fall off.
IF LEG FALLS:

Holding leg vertically, push

leg firmly up while pushing

the motor unit down.

Step 5.

Open the swing legs completely.

Snap plastic leg braces onto

outside of legs. The plastic pins

inside the ends of the braces

will fit into the dimples on the

legs.
Pull on the leg brace tab to

take off.

Do not use

swing without the leg braces.

8

Wire end

Round

end

(not oval)

6

7

5

165-11-95 IS1554

Dimple

Hold tube

vertically

Flattened

side

Plastic peg

Attaching the Hanger

Step 1.

With crossbar of hanger

toward front of the motor unit,

line up holes in hanger brackets

with holes on the sides of motor

unit.

Step 2.

Insert screws into both brackets

as shown. Fasten with acorn

nuts using the enclosed hex

wrench. Tighten nuts firmly with

hex wrench and screwdriver.

Adjusting the Handle

To bring carrier handle from

resting position into position for

carrying or swinging, first set

the carrier down. Then push

down on center of handle, and

rotate the handle forward until it

clicks into the locked position.

To return the handle to resting

position, first set the carrier

down. Then push down on

center of handle, and rotate the

handle backward until it clicks

into place.

NOTE: It is normal for the

handle to seem loose in the

resting position.

Push down

on center

of handle

Push down

on center

of handle

Different uses for infant carrier...

Cuddler

Carrier

Feeder

...or as a Rocker.

Using the Carrier

Lift carrier in and out of swing.

Do not adjust

the handle while carrier is on

swing.

Step1.

With baby out of swing, open

the battery compartment by

gently pressing on the lid at the

ridged area and lifting the lid.

Installing Batteries

NEVER INSERT OR REMOVE

BATTERIES WITH BABY IN THE SEAT. THEY COULD

FALL ON BABY IF DROPPED!

Step 2.

Insert two “D” cells. Alkaline

or Ni-Cad “D” cells are best.

Be sure the batteries are put in

correctly. (Swing will not run if

batteries are put in backwards.)

Step 3.

Snap the lid closed.

Hanger

Notch

Step 2.

Snap handle and hinges

together to lock.

Be sure

handle is locked into the

plastic hinges.

Step 3.

Place cradle in hanger.

Be sure handle notches are

seated in the hanger.

Starting the Cradle

Step 1.

Place your child in the cradle.

Step 2.

Set the CONTROL switch

between the low and center

positions. Your cradle will swing

properly only in the lower range.

Step 3.

Push ON/OFF switch to the

“on” position.

Step 4.

PUSH CRADLE TO START. BE SURE YOU PUSH

IT UP HIGH ENOUGH FOR THE MOTOR TO GET A

GOOD START.

NOTE: Draping a small blanket over side of cradle will

slow the swinging motion.

Using the Tray

Unlatch the tray by squeezing

the two latches under the tray

at the same time, and lift up

tray. Be careful not to let tray

hit your baby when lifting or

closing tray.

To latch tray, push down firmly.

Tray must be latched at all

times when baby is in the

swing.

Adjusting the Stand

To change recline of the carrier,

squeeze the adjustment wire

and move to desired position.

To adjust for rocking, move the

adjustment wire to the highest

position.

Do not change

recline with baby in carrier.
Be aware that infant move-

ment or rocking may cause

the carrier to move on a table.

Using the Cradle

REMOVE LAW TAGS FROM

THE CRADLE PAD BEFORE

USING THIS CRADLE.

Step 1.

Lift top frame of cradle, and

turn handle so that it lines up

with the plastic hinges.

Not intended for use as a night-time

bed or car bed.