Garmin POWERLITE 85+ - Manual (Page 4)

Troubleshooting
If you see a blank screen...
If you see a blank screen or the No signal message after turning on your
computer, check the following:
• Make sure the power light on the projector is green and not flashing, and
the A/V Mute slide is open.
• Press the Source Search button on the projector or remote control to
select the computer as the image source.
• If you’re using a Windows notebook, press the function key on your
keyboard that lets you display on an external monitor (allow a few
seconds for the projector to sync up after you press the key). It may be
labelled CRT/LCD or have an icon such as
. You may have to hold
down the Fn key while pressing it.
If the projector and notebook don’t display the same
image...
Windows
Try using the CRT/LCD or key as described above. On most systems, this
key lets you toggle between the LCD screen and the projector, or display on
both at the same time.
If that doesn’t work, check your monitor settings to make sure both the LCD
screen and the external monitor port are enabled.
1 From the Windows Control Panel, open the Display utility and select
Settings or Change display settings. In Windows Vista
® , right-click on
the desktop and select Personalize, then select Display Settings.
2 Select Advanced or Advanced Settings.
3 The method for adjusting the setting varies; you may have to click a
Monitor tab, then make sure the external monitor port is set as your
primary display and/or enabled.
Mac OS X
1 From the Apple ® menu, select System Preferences, then select Display
or Displays.
2 Click Detect Displays.
3 Make sure the VGA Display or Color LCD dialog box is selected.
4 Click Arrangement or Arrange, then make sure Mirror Displays is
selected.
Network configuration
If you need to configure the projector for your network, you can use the
projector’s menu system.
NOTE: If you’re using the optional Wireless 802.11a/b/g Module, see the
User’s Guide on your projector CD for configuration instructions.
1 Press the Menu button on the remote control, select the Network
menu, then press Enter.
2 Choose Network Configuration and press Enter.
3 Select the Wired LAN menu and press Enter.
4 Choose IP Settings and press Enter. You see a screen like the
following:
5 Do one of the following:
• If your network assigns addresses automatically, turn on the DHCP
setting.
• If your network does not assign addresses automatically, turn off
DHCP and enter the projector’s IP Address, Subnet Mask, and
Gateway Address, as needed.
To enter numbers, use the buttons on the remote control to
highlight the number you want to input, then press the Enter button.
When you’re finished entering an address in the network menu, press
the Esc button to return to the previous menu.
6 To prevent the IP address from appearing on the standby screen, set the
IP Address Display setting to Off.
7 When you’re done making all necessary changes, press the Esc button
to return to the previous menu, select Complete, and press the Enter
button to save your settings. Then press Enter again to confirm.
8 Press the Menu button to exit the menu system.
Epson is a registered trademark and Epson Exceed Your Vision is a registered logomark of Seiko Epson
Corporation. PowerLite and PrivateLine are registered trademarks of Epson America, Inc.
General Notice: Other product names used herein are for identification purposes only and may be trademarks
of their respective owners. Epson disclaims any and all rights in those marks.
This information is subject to change without notice.
© 2009 Epson America, Inc. 12/09
Printed in XXXXXX
CPD-27777
Project over the network
Install EasyMP ® Network Projection and EasyMP Monitor (Windows only) on
each computer that will project over the network. Use the CD labeled Epson
Projector Software for Meeting & Monitoring to install the software.
If you need to configure the projector for your network, see “Network
Configuration.”
1 Press the LAN button on the remote control.
2 Start EasyMP Network Projection on your computer.
Windows: Select or Start > Programs or All Programs > EPSON
Projector > EasyMP Network Projection > EasyMP Network
Projection V2.XX.
Mac OS X: Double-click the EasyMP Network Projection icon in your
Applications folder.
3 Select Advanced Connection Mode and click OK.
4 Select the projector you want to connect to, then click Connect.
If you don’t see the projector you want, click the Automatic search
button. If you still don’t see the projector, click the Manual Search
button and enter the projector’s IP address.
5 If you see a message asking for a keyword, enter the four digits that
appear on the LAN standby screen and click OK.
Your computer image is projected, with a floating toolbar:
When you’re done presenting, click Disconnect on the toolbar.
NOTE: Using the optional Wireless 802.11a/b/g Module, you can project
wirelessly. To purchase the Wireless 802.11a/b/g Module or other
accessories, see “Optional Accessories.” For more information about using
the projector on a network, see your User’s Guide and EasyMP Network
Projection Operation Guide on your projector CD.
Where to get help
Manuals
For more information about using the projector, install the manuals from your
projector CD.
Telephone Support Services
To use the Epson PrivateLine ® Support service, call (800) 637-7661 and enter
the PIN on the Epson PrivateLine Support card included with your projector.
This service is available 6
AM to 6 PM , Pacific Time, Monday through Friday, for
the duration of your warranty period. You may also speak with a projector
support specialist by dialing:
(562) 276-4394 (U.S.) or (905) 709-3839 (Canada), 6 AM to 6 PM , Pacific Time,
Monday through Friday
Days and hours of support are subject to change without notice. Toll or long
distance charges may apply.
Internet Support
Visit epson.com/support for solutions to common problems. You can
download utilities and documentation, get FAQs and troubleshooting advice,
or e-mail Epson with your questions.
Registration
Register today to get product updates, special promotions, and customer-only
offers. You can use the CD included with your projector or register online at
www.epson.com/webreg.
Optional accessories
For a list of optional accessories, see the User’s Guide on your projector CD.
You can purchase screens, carrying cases, or other accessories from an Epson
authorized reseller. To find the nearest reseller, call 800-GO-EPSON
(800-463-7766). Or you can purchase online at www.epsonstore.com (U.S.
sales) or www.epson.ca (Canadian sales).
4118552 Rev.0
1-B
C
4118552 Rev.0
1-B
M
4118552 Rev.0
1-B
Y
4118552 Rev.0
1-B
K