FELLOWES HS-800 - Manual (Page 2)

Refer to separate setup instructions for proper assembly. Disconnect power switch must be in ON position to operate shredder. Insert waste bag (Fellowes
#36056) for easy disposal.
p p p p
ENGLIS ENGLISH ENGLISH ENGLISH ENGLISH ENGLISH ENGLISH ENGLISH ENGLISH ENGLISH ENGLISH ENGLISH ENGLISH ENGLISH ENGLISH NGLISH NGLISH NGLISH GLISH GLISH GLISH GLISH LISH LISH ISH SH SH SHHHH
Models HS-800 MMM d M d M d M d l Models Models Models HS-800
Paper entry
Bin
Door
CAPABILITIES
Will shred: Paper
Will not shred: Adhesive labels, transparencies, newspaper, credit
cards, cardboard, paper clips, staples, laminates or plastic other than
noted above
Paper shred size:
High Security Cross-Cut......................... 1/25” x 3/16” (1 x 4.7mm) Maximum:
Sheets per pass ............................................................................. 8*
Sheets per day .........................................................................5,000
Paper entry width........................................................16” (400 mm)
* 20lbs., 8.5”x11” paper at 120v, 60Hz,
14 Amps; heavier paper, humidity
or other than rated voltage may reduce capacity. Recommended daily
usage rates: 5,000 sheets per day.
IMPORTANT SAFETY INSTRUCTIONS — Read Before Using!
Keep hands
away from paper entry. Always set to
Off ( ) or unplug when not in use.
• Keep foreign objects – gloves, jewelry, clothing,
hair, etc.– away from shredder openings. If
object enters top opening, switch to Reverse ( )
to back out object.
• Never use aerosol, petroleum-based or other flammable
products on or near shredder. Do not use canned air
on shredder.
• Do not use if damaged or defective. Do not open
shredder head. Do not place near or over heat or
water source.
• 8 sheets per pass to avoid jams.
• Avoid touching exposed blades under High Security Cross-Cut
shredder head.
• The grounded socket-outlet shall be installed near the equipment
and shall be easily accessible.
• Make sure shredder gets suffi cient ventilation (ventilating grills
must be kept free).
2
Shredder head Control panel
See safety instructions below
Set to Off Press Auto-On/Off
Feed into paper entry
and release
across entry
Press Forward
button
Press Forward
button
*Only use a non-aerosol vegetable oil in long nozzle container such
as Fellowes #35250
Shred one sheet Press Reverse button
Lubricate machine before
starting to shred, after
every 10 minutes of
continuous shreddering,
or immediately if:
• Capacity decreases
• Motor sounds different, or
shredder stops running
Indicator lights:
tightly closed (yellow)
Paper Jam (red)
Remove and
empty bin (yellow)
Follow oiling procedure below and repeat twice.
Shredder will
automatically
Reverse out
paper
Remove all uncut
paper from entry
Press Forward for 5 seconds to clear
cutters. Press Forward button again
to resume Auto start
Bin Full (yellow)
Jam (red)
Reverse
Forward
(toggle)
Auto
On/Off
(green)
Door Open (yellow)
OPERATION
TROUBLESHOOTING
Paper jam: Set to Off (O) and empty bin. Replace bin, close door, and follow any or all of the below procedures.
MAINTENANCE
WARRANTY
LIMITED WARRANTY Fellowes, Inc. (“Fellowes”) warrants the cutting blades of the
machine to be free from defects in material and workmanship for
, g ,
5 years from
the date of purchase by the original consumer. Fellowes warrants all other parts
p y
of the machine to be free of defects in material and workmanship for 2 year from
p y g p p y g p
the date of purchase by the original consumer. If any part is found to be defective
p y p y
during the warranty period, your sole and exclusive remedy will be repair or
p y g y p p y g y p
replacement, at Fellowes’ option and expense, of the defective part.
g y p , y y g y p , y
This warranty does not apply in cases of abuse, mishandling, or unauthorized
p , p p , p p , p p ,
repair. ANY IMPLIED WARRANTY, INCLUDING THAT OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE, IS HEREBY LIMITED IN DURATION TO THE
APPROPRIATE WARRANTY PERIOD SET FORTH ABOVE. In no event shall Fellowes be
,
liable for any consequential or incidental damages attributable to this product.
This warranty gives you specific legal rights. The duration, terms, and conditions of
y q g p y q g p
this warranty are valid worldwide, except where different limitations, restrictions,
y g y p g g , , y g y p g g ,
or conditions may be required by local law.
y , p y ,
For more details or to obtain service under this warranty, please contact us or
y q y y q y
your dealer.
3
CLEANING AUTO-START INFRARED SENSORS
TO CLEAN THE SENSORS
Paper detection sensors are designed for maintenance free operation. However, on rare occasions the sensors may become blocked by paper dust
causing the motor to run even if there is no paper present (Note: two paper detection sensors are located in the center of the paper entry).
Mounting for
paper-tray
Disconnect power switch (red)
After a jam, all lights on machine go off and machine doesn’t go back on. Open door and reset circuit breaker.
Circuit breaker
Form feed paper-tray
Mounts on front or back
of shredder.
Using cotton swab, wipe away
any contamination from the
paper sensors.
1 3
Locate Auto-start infared
sensor.
2
Dip cotton swab in rubbing
alcohol.