FUNAI MJ414FG - Manual (Page 2)

1 2 3
4 5 6
7 8 9
0 +100
DISPLAY
VOL
CH
CH
VOL
SLEEP
CHANNEL
RETURN
MUTE
GAME POWER
MENU
VIDEO AUDIO EARPHONE MENU VOLUME CHANNEL POWER
VIDEO AUDIO EARPHONE MENU VOLUME CHANNEL POWER
PREPARATION FOR USE
CONNECTIONS
ANT . IN
ANT. IN IN OUT
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO
WIDE SLOT, FULLY INSERT.
ATTENTION: POUR ÉVITER LES CHOC ÉLECTRIQUES, INTRODUIRE LA LAME LA
PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET
POUSSER JUSQU’AU FOND.
[EXTERNAL CONNECTION]
Front AUDIO/VIDEO input
VIDEO AUDIO
Video Cable
Audio Cable Video Game Video Camera
Front of this TV
Notes:
● If you press [GAME] when the TV is off, the TV turns on and enters in Game mode.
● If you adjust another picture control while in Game mode, this mode will automatically
be canceled.
ex.
Plug the incoming cable into the ANT. IN jack on the rear of the TV.
OPERATIONS
Note:
● If some digits appear in the corner of the screen when the unit is turned on for the first time,
press [POWER] without unplugging the power cord.
REMOTE CONTROL AND FRONT PANEL FUNCTION
Infrared Sensor Window
POWER button
To turn TV on/off
CHANNEL ▲/▼ buttons
To select channels
VOLUME X X /Y Y buttons
To adjust volume
MENU button
To view on-screen menu
AUDIO input jack
VIDEO input jack
INSTALLING THE BATTERIES
Install two AA batteries (supplied)
matching the polarity indicated inside
battery compartment of the remote con-
trol.
[BATTERY PRECAUTIONS]
• Be sure to follow the correct polarity as indicated in the battery compartment.
Reversed batteries may cause damage to the device.
• Do not mix different types of batteries together (e.g. Alkaline and Carbon-Zinc) or old batteries
with fresh ones.
• If the device is not to be used for a long period of time, remove the batteries to prevent
damage or injury from possible battery leakage.
• Do not try to recharge batteries not intended to be recharged; they can overheat and rupture.
2 1 3
SELECTING AUDIO/VIDEO INPUT
You can select external input jacks by pressing [GAME] on the remote control.
EARPHONE jack
1 1
GAME
GAME
To use external input
Picture: GAME (ON)
Input:
External
2 2
15
To return to TV channel
GAME
In the Game mode, you can use front input jacks with suitable picture adjustments for video games.
(OUT)
(IN)
(IN)
(OUT)
2 2
[-] GAME MODE [+]
OFF ON
VIDEO
To cancel Game mode only
3 3
Picture: Customized
Input: External
15
To return to TV channel
GAME
MENU
VOL
You can enter into Video mode from Game mode by adjusting a Picture control.
2 times
1 1
GAME
GAME
To use external input
Picture: GAME (ON)
Input: External
Select “PICTURE”
Note:
• For your safety and to avoid damages to the unit, unplug the antenna cable from the
ANT. IN jack before moving the unit.
After 10 seconds
*Note (DO NOT DISCONNECT FROM BOX)
Some cable TV systems use scrambled signals and
require a special converter to receive these channels.
Consult your local cable company.
OR
Incoming cable from home Antenna /
Cable Company (No Cable Box)
Incoming cable from Cable
Company or Satellite Antenna
Cable Box or
Satellite Box*
Cable
TV signal
Antenna
Rear of this TV
OR
Cables not included
Note:
● You can test if the remote control sends out the infrared signal with an AM radio.
(Refer to “TROUBLESHOOTING GUIDE”.)
POWER button
To turn TV on/off
CH(ANNEL) K K / L L buttons
To select channels and move
up/down through menu items
GAME button
Press to set the Game mode
DISPLAY button
To display CH No./Audio Status
CHANNEL RETURN button
To return previous screen
VOL(UME) K K / L L buttons
To adjust volume
To decide the command of settings
IR transmitter
To send infrared ray (IR) signal
Channel number buttons
Press two digits to directly access the
desired channel. Remember to press
a "0" before a single digit channel.
MENU button
To view on-screen menu
MUTE button
To mute sound
SLEEP button
To set Sleep Timer
SELECTING AUDIO/VIDEO INPUT
You can select external input jacks by pressing [GAME] on the remote control.
Notes:
● In case no channel can be received by the channel scanning, “NO TV SIGNALS” is displayed on
the screen. Turn off the unit and check the antenna connection, then follow step 1 again.
● If those settings do not work properly, please call our help line in the warranty.
2 2 If the TV screen shows
snow noise and there
is no operation for
more than 10 seconds,
“HELPFUL HINTS”
appears. Follow the
instructions listed on
the screen. 1 1 Select the desired
language according to
the screen indication.
After that, the TV
performs “AUTO
PRESET CH” to scan
channels available for
the broadcasting in
your area.
When the scanning is completed, or [MENU] is pressed during channel scanning to cancel it, the
tuner stops on the lowest memorized channel.
- HELPFUL HINTS -
1. PLEASE CHECK TO SEE IF
THE ANTENNA/CABLE/
SATELLITE IS PROPERLY
CONNECTED.
2. DID YOU PERFORM
“AUTO PRESET CH” ?
3. PLEASE REFER TO FRONT
PAGE OF THE OWNER’S
MANUAL OR REAR PANEL
FOR SUPPORT LINE
INFORMATION.
SELECT LANGUAGE
ENGLISH
NEXT:PRESS CHK
ESPAÑOL
DESPUÉS:PRESIONE CHL
FRANÇAIS
APRÈS:PRESSEZ VOLK
– INITIAL SETUP –
PLEASE CONNECT ANTENNA
OR CABLE OR SATELLITE
TO THIS UNIT.
THEN PRESS CH K,
IN ORDER TO PERFORM
“AUTO PRESET CH”.
INITIAL SETUP
When you turn on the power for the first time, the “SELECT LANGUAGE” menu is displayed.
The “INITIAL SETUP” menu is displayed every time you turn on the unit unless the scanning is
completed.