Fender 410 PRO User Manual
Page 6
w
ww
ww
w.
.f
f e
e n
n d
d e
e r
r.
.c
co
om
m
✧
w
ww
ww
w.
. m
m r
r g
g e
e a
a r
r h
h e
e a
a d
d .
.n
ne
et
t
6
F
F
F
F
e
e
e
e
n
n
n
n
d
d
d
d
e
e
e
e
rr
rr
®
4
4
4
4
1
1
1
1
0
0
0
0
P
P
P
P
rr
rr
o
o
o
o
S
S
S
S
T
T
T
T
L
L
L
L
o
o
o
o
u
u
u
u
d
d
d
d
s
s
s
s
p
p
p
p
e
e
e
e
a
a
a
a
k
k
k
k
e
e
e
e
rr
rr
E
E
E
E
n
n
n
n
c
c
c
c
ll
ll
o
o
o
o
s
s
s
s
u
u
u
u
rr
rr
e
e
e
e
Your new 410 Pro ST Bass Loudspeaker Enclosure is
constructed from 3/4" (1.9 cm) 7-ply Birch/Maple
Plywood and is capable of handling 300 Watts of con-
tinuous power. The 410 Pro ST features four 10"
(25.4 cm) speakers with 44 oz (1.25 kg) magnets and is
designed for use with a Fender
®
Bassman
®
1200,
Bassman
®
300, Bassman
®
400 Head or other profes-
sional quality bass amplifier. Please read these instruc-
tions and the instructions that came with your amplifier
before making connections. Follow all equipment cau-
tion and safety labeling.
SPEAKER CONNECTIONS
Use 16 gauge (or heavier) speaker cable with one of the
three types of input connections on your 410 Pro:
A) Phone jacks with a standard 1/4" plug
B) Binding posts with dual “banana” plug or
stripped wires
C) Speakon
®
connector with Speakon
®
plug
Multiple 410 Pro ST cabinets can be linked as illustrat-
ed, when additional output is needed. Note: Follow the
speaker impedance load guidelines set by the manufac-
turer of your amplifier to avoid damage to your equip-
ment.
HORN TWEETER
The horn tweeter is protected from power-overload
damage by an incandescent lamp. If the horn tweeter
stops responding, replace the lamp as you would a
blown fuse. The lamp and a spare (reorder
P/N
051857) are located on the circuit board on the inside
of the input jack panel.
Lamp Replacement:
1) Remove the 4 screws from the input jack panel cor-
ners.
2) Pull the panel out, then up.
3) Use a small flathead screwdriver to remove the
blown lamp which is visible through a cutout in the
circuit board.
4) Remove the spare lamp stowed on the side of the
circuit board and install it where the blown lamp was
located.
5) Install the input jack plate in the reverse order of
removal.
SPECIFICATIONS
PART NUMBER:
2217100000
DRIVERS:
Four 10" (25.4 cm) Fender
Special Design Cast Frame
Woofers
2" (5.1 cm) Voice Coil, 44 oz
(1.25 kg) Magnet
One Horn Tweeter
1" (2.5 cm) Voice Coil, 8 oz
(0.23 kg) Magnet
CABINET:
3/4" (1.9 cm) 7-ply
Birch/Maple Plywood
SENSITIVITY:
94 dB, 1 Watt - 1 Meter
POWER HANDLING:
300 Watts, Continuous
600 Watts, Program
IMPEDANCE:
8
Ω
CONNECTIONS:
Dual, Parallel Wired, 1/4”
High Current Input Jacks,
Binding Posts and
Speakon
®
Connector
ENCLOSURE VOLUME:
V
B
= 4.8 ft
3
(135 l)
DIMENSIONS:
Height:
25.5 in
(64.8 cm)
Width:
25.5 in
(64.8 cm)
Depth:
18.5 in
(47.0 cm)
WEIGHT:
87 lb
(39.6 kg)
Product specifications are subject to change without notice.
A PRODUCT OF:
FENDER MUSICAL INSTRUMENTS CORP.
CORONA, CA USA
Fender
®
is a registered trademark of FMIC,
Speakon
®
is a registered trademark of Neutrik.
Copyright © 2002 FMIC