haier HWM65-828 - Manual (Page 6)

After you open the package, please lean
the washing machine gently down on soft
items ( like the towel cloth, blanket, etc. ).
Install the bottom plate to the bottom of
the machine, then lift the machine up
gently. See to the figure:
Back
Front
Soft items Bottom plate
Please install and adjust the machine according to the requirement of the manual.
It is very important to your security and correct operating the machine.
Install the bottom plate
Installation and adjustment
I
Section I enlarging
Two claws at the bottom cover shall
be inserted in two bar-shaped holes
in the stand. Make sure the claws
are firmly in place.
Fasten the bottom plate to
base frame with one screw
Install the inner cover component
1.Open the top lid of the washing machine.
2.Put the inner cover component on the outer tub cover, aiming the inner cover
shaft to the installation hole of the corresponding outer tub cover shaft groove.
3.Firstly insert the inner cover shaft of one side into the corresponding outer tub
cover shaft groove, then push the another inner cover shaft into the corresponding outer
tub cover shaft groove. Please install to designated position to guarantee there are no
dropping or abnormal sound in opening and closing of the inner cover, and the operation
shall be smooth. Do not dismount the inner cover component after washing.
Outer tub cover
Outer tub cover shaft groove
Inner cover shaft
Inner cover component
Figure 1
Right hand
Left hand
Figure 2
1.Push "POWER" button to switch on the power
2.Push "PROGRAM" button to select suitable full-auto program
Steps of using the operation buttons and description of each step
After the power is switched on, "STANDARD" is automatically set. To select other full-auto programs, please push
the "PROGRAM" button till the corresponding indicator is on. Refer to the "PROGRAM" button on Page 11.
E.g. Set to "SPEEDY"program for small quantity of laundries with light soil.
When a standard cycle is selected, the fuzzy program is run. The water level and the washing time can be
selected according to be texture and volume of the laundry. The washing cycle is automatically controlled.
I DELAY button "+ - "
Push down the to select the reserve time(2h-24h). "+ - "
Push the button can display the reserve state. "+ - "
SOAK
For GENTLE program, press SET button can change the process,
can not change time.
"SOAK"button ,then press "+ - "
J "SOAK " button
K Reserve, remain time digitron
It displays "--" during detecting.
It displays remained reserve time (hour).
It displays abnormal symbol in abnormal situation.(See to Page16)
You can choose "RESERVE WATER" function to keep the after rinsing water.
Washing machine will keep the after rinsing water once finish rinsing in tub about 4 hours, and buzzer every 15
minutes.( For example, if you choose "SECOND RINSE", the machine only keep the after second rinsing water,
If you choose "FIRST RINSE" and "SECOND RINSE" together, the machine will keep the after first and second
rinsing water)
Press"START/PAUSE" button or open and close the top lid one time to collect the after rinsing water, then the
machine will go on for next program.
If you don't collect the after rinsing water within 4 hours, the machine will drain automaticly, then go on for
next program.
L RESERVE WATER " " button
M SET "+ - " button
Refer to the description of operation button
13
RESERVE
WATER
The button is unavailable from the SPEEDY , WOOL and TUB DRY programs.
It has the special power resume function. In the case of power failure or the power plug is loose
during running , the machine can save the running program, and resume the program after the
power supply is recovered. You do not need to set the program again.
Press the button, the light flashes then press SET to select the desired soak time
from the STANDARD, HEAVY,CHILD, MEMORY programs( 0,10, 20,30,40 minutes).
"SOAK " "+ - "
Press the button to select soak . "SOAK " procedure