Holmes HASF1406 - Manual (Page 2)

A. (1) L-shaped screw
B. (1) Washer
C. Weight
D. Base
E. Long Extension Pole
F. (2) Phillips head screws
G. Short Extension Pole
H. Neck
I. Tilt Adjustment Knob
J. Fan Speed Pull Chain
K. Motor Housing
L. Oscillation Knob
M. Motor Shaft
N. Grill Clips
O. Rear Grill
P. Rear Grill Nut
Q. (1) Blade screw
R. Blade
S. Hanging Clip
T. Front Grill
6. Secure the Front Grill (T) to the Rear Grill of the fan by
positioning the hanging clip of the Front Grill over the
Rear Grill. Close the remaining four Grill Clips (N) of
the Front Grill over the Rear Grill. Refer to Figure 8.
ADJUSTMENT INSTRUCTIONS
Fan Head Tilt Adjustment
Loosen Tilt-Adjustment Knob (I), move fan head to desired
angle, and tighten Tilt Adjustment Knob to lock in place.
OPERATING INSTRUCTIONS
Fan Speed Pull Chain (J)
1st = High ( III )
2nd = Medium ( II )
3rd = Low ( I )
4th = Off (
o
)
Oscillation Knob (L) ( )
Push, Pull = Oscillation On, Off
CLEANING/MAINTENANCE INSTRUCTIONS
Follow these instructions to correctly and safely care for
your fan.
• Always unplug the fan before cleaning or disassembling.
• Be sure to clean your fan with a soft cloth moistened
with a mild soap solution.
• Do not allow water to drip on or enter into the fan
motor housing.
• Do not use gasoline, thinner, or benzene as a cleaner.
• Lightly run a vacuum cleaner nozzle over the fan grill
to remove any dust or dirt that may have accumulated.
FAN BLADE CLEANING
Make sure the fan is unplugged before disassembling and
cleaning the fan blade. Unclip and remove the front grill.
Wipe the blade with a soft cloth moistened with a mild soap
solution. DO NOT allow any liquid to drip into or enter the
Motor Housing. Re-clip the front grill onto the fan. Make
sure all parts are secured prior to operating the fan.
FAN STORAGE INSTRUCTIONS
Your fan should be stored in the off-season in its original
box. It is important to keep it in a safe, dry location.
• We recommend using the original (or appropriately
sized) box.
• Please remember to protect the fan from dust or
moisture.
P L E A S E R E A D A N D S AV E T H E S E
I M P O R TA N T S A F E T Y I N S T R U C T I O N S
F E AT U R E S - O P E R AT I O N S
When using electrical appliances, basic safety precautions
should always be taken including the following:
1. Read all instructions before using this appliance.
2. Use fan only for purposes described in the instruction
manual.
3. To protect against electrical shock do not immerse unit,
plug or cord in water or spray with liquids and plug
the appliance directly into a 120V AC electrical outlet.
4. Close supervision is necessary when any appliance is
used by or near children.
5. Unplug from outlet when not in use, when moving
fan from one location to another, before putting on
or taking off parts and before cleaning.
6. Avoid contact with moving parts.
7. Do not operate in the presence of explosive and/or
flammable fumes.
8. To avoid fire hazard, NEVER place the cord under
rugs or any parts near an open flame, cooking or
other heating appliance.
9. Do not operate any appliance with a damaged cord
or plug after the appliance malfunctions, or has been
dropped/damaged in any manner.
10. The use of attachments not recommended or sold by
the appliance manufacturer may cause hazards.
11. Do not let the cord hang over the edge of a table,
counter or come in contact with hot surfaces or leave
exposed to high traffic areas.
12. Do not use outdoors.
13. To disconnect, grip plug and pull from wall outlet.
Never yank on cord.
14. Always use on a dry, level surface.
15. Do not operate fan until fully assembled with all
parts properly in place.
16. This product is intended for household use ONLY and
not for commercial or industrial applications.
17. WARNING: To reduce the risk of electrical shock
and injury to persons, do not use in window.
18. WARNING: To reduce the risk of fire or electric shock, DO
NOT use this fan with any solid-state speed control device.
PLEASE READ AND SAVE
THESE IMPORTANT SAFETY
INSTRUCTIONS
ASSEMBLY INSTRUCTIONS
Tools required: One Phillips head screw driver
Assembly time: 10-15 minutes
1. Secure the Base Weight (C), Base (D), and Long
Extension Pole (E) together using the L-shaped screw
(A) and Washer (B). Refer to Figure 3 for the correct
alignment of the Long Extension Pole to the Base.
2. Align the holes of the Long Extension Pole (E) and
Short Extension Pole (G) together and secure with
Phillips head screw (F) and tighten with screw driver.
Refer to Figure 4.
3. Align the holes of the neck of the Short Extension Pole and
the Neck (H) together and secure with the Phillips head
screw (F) and tighten with screw driver. Refer to Figure 5.
4. Secure the Rear Grill (O) to the Motor Housing (K) by
tightening the Rear Grill Nut (P). Refer to Figure 6
for correct positioning of the Rear Grill to the Motor
Housing.
5. Secure the Fan Blade (R) to the Motor Shaft (M) by
tightening the Blade Screw (Q) with a screw driver.
Refer to Figure 7 for the correct alignment of the Fan
Blade to the Blade Shaft.
F E AT U R E S - O P E R AT I O N S
C L E A N I N G / M A I N T E N A N C E
THIS APPLIANCE HAS A POLARIZED PLUG (one blade is wider than the
other). To reduce the risk of electric shock, this plug is intended to fit in
a polarized outlet only one way. If the plug does not fit fully in the
outlet, reverse the plug. If it still does not fit, contact a qualified
electrician to install the proper outlet.
DO NOT ATTEMPT TO MODIFY THIS PLUG OR DEFEAT THIS
SAFETY FEATURE IN ANY WAY.
D
Figure 1
P
R
M
J
O
I
G
T
H
L
C
K
E
Figure 2
A (X 1)
Q (X 1), F (X 2)
3 pt
B
Q
Figure 3
Figure 4
Figure 5
Figure 6
Figure 8
S
N
S
P
F
A
F
A
B (X 1)
B
E
D
C
G
E
F
H
G
O
Figure 7
If you have any questions regarding your product or would
like to learn more about other Holmes ® products, please
contact our Consumer Service Department at 1-800-546-
5637 or visit our website at www.holmesproducts.com
HASF1406_07EM1.qxd 9/29/07 10:38 Page 2