Harman-Kardon AVR 110 - Manual (Page 10)

10 REAR PANEL CONNECTIONS
Rear Panel Connections
¡ Tape Inputs: Connect these jacks to the
PLAY/OUT jacks of an audio recorder.
™ Tape Outputs: Connect these jacks to the
RECORD/INPUT jacks of an audio recorder.
£ Video 1 Audio Inputs: Connect these
jacks to the PLAY/OUT audio jacks on a VCR
or other video source.
¢ AM Antenna: Connect the AM loop antenna
supplied with the receiver to these terminals. If an
external AM antenna is used, make connections
to the AM and GND terminals in accordance
with the instructions supplied with the antenna.
∞ Video 1 Audio Outputs: Connect these
jacks to the RECORD/INPUT audio jacks on
a VCR.
§ DVD Audio Inputs: Connect these jacks
to the analog audio jacks on a DVD or other
video source.
¶ FM Antenna: Connect the supplied indoor or
an optional external FM antenna to this terminal.
• CD Inputs: Connect these jacks to the out-
put of a compact disc player or CD changer.
ª Digital Audio Outputs: Connect these
jacks to the matching digital input connector
on a digital recorder such as a CD-R or
MiniDisc recorder.
‚ DVD Video Inputs: Connect these jacks to
the composite or S-Video output jacks on a
DVD or other video source.
⁄ Video Monitor Outputs: Connect this
jack to the composite or S-Video input of a TV
monitor or video projector to view the output
of any standard video source selected by the
receiver’s video switcher.
¤ Subwoofer Output: Connect this jack to
the line-level input of a powered subwoofer. If
an external subwoofer amplifier is used, con-
nect this jack to the subwoofer amplifier input.
‹ Front Speaker Outputs: Connect these
outputs to the matching + and – terminals on
your front left/right speakers.
› Center Speaker Outputs: Connect these
outputs to the matching + and – terminals on
your center-channel speaker.
fi Surround Speaker Outputs: Connect
these outputs to the matching + and – termi-
nals on your left and right surround speakers.
NOTE: When making speaker connections
always make certain to maintain correct polarity
by connecting the red (+) terminals on the
AVR 110 to the red (+) terminals on the speak-
ers and the black (–) terminals on the AVR 110
to the black (–) terminals on the speakers.
See page 14 for more information on speaker
polarity.
fl Switched AC Accessory Outlet: This
outlet may be used to power any device you
wish to have turned on when the AVR 110 is
turned on with the System Power Control
switch
2.
‡ Unswitched AC Accessory Outlet: This
outlet may be used to power any AC device.
The power will remain on at this outlet regard-
less of whether the AVR 110 is on or off.
NOTE: The total power consumption of all
devices connected to the accessory outlets
should not exceed 100 watts.
° AC Power Cord: Connect the AC plug to
an unswitched AC wall output.
· Remote IR Output: This connection per-
mits the IR sensor in the receiver to serve other
remote controlled devices. Connect this jack to
the “IR IN” jack on Harman Kardon (or other
compatible) equipment.
a Remote IR Input: If the AVR 110’s front
panel IR sensor is blocked due to cabinet
doors or other obstructions, an external IR
sensor may be used. Connect the output of
the sensor to this jack.
b Video 1 Video Outputs: Connect these
jacks to the RECORD/INPUT composite or
S-Video jack on a VCR.
c Video 1 Video Inputs: Connect these
jacks to the PLAY/OUT composite or S-Video
jacks on a VCR or other video source.
d Video 3 Video Inputs: Connect these
jacks to the PLAY/OUT composite or S-Video
jacks on a VCR or other video source.
e Video 2 Video Inputs: Connect these
jacks to the PLAY/OUT composite or S-Video
jacks on a VCR or other video source.
f Video 2 Video Outputs: Connect these
jacks to the RECORD/INPUT composite or
S-Video jacks on a VCR.
g Optical Digital Inputs: Connect the opti-
cal digital output from a DVD player, HDTV
receiver, LD player or CD player to these jacks.
The signal may be either a Dolby Digital signal,
a DTS signal or a standard PCM digital source.
h Coaxial Digital Inputs: Connect the coax
digital output from a DVD player, HDTV receiver,
LD player or CD player to these jacks. The signal
may be either a Dolby Digital signal, DTS signal
or a standard PCM digital source. Do not con-
nect the RF digital output of an LD player to
these jacks.
i Video 2 Audio Outputs: Connect these
jacks to the RECORD/INPUT audio jacks on a
VCR or other video source.
j Video 3 Audio Inputs: Connect these
jacks to the PLAY/OUT audio jacks on a VCR
or other video source.
k Video 2 Audio Inputs: Connect these
jacks to the PLAY/OUT audio jacks on a VCR
or other video source.