Harman-Kardon AVR 760 - Manual (Page 8)

8
ADVANCED FuNCTIONS
Step four – Setting channel output Levels
manually
For a conventional 2-channel receiver, the balance control affects the stereo
imaging by adjusting the relative loudness of the left and right channels.
With up to seven main channels, plus a subwoofer, imaging becomes both
more critical and more complex. The goal is to ensure that each channel is
heard at the listening position with equal loudness.
EzSet/EQ II calibration can handle this critical task for you, simply and
automatically. However, the AVR’s Adjust Speaker Levels menu allows you
to calibrate the levels manually, either using the system’s test tone or while
playing source material.
Make sure all speakers have been placed and connected correctly. 1.
Adjust the number of speakers, crossover, distance and sub mode for each 2.
speaker in your system, as described in Step Three.
Measure the channel levels in one of these ways, and adjust the channel 3.
levels using the Adjust Speaker Levels menu:
Preferably, use a handheld SPL meter set to the C-Weighting, Slow a)
scale. Adjust each channel so that the meter reads 75dB.
By ear. Adjust the levels so that all channels sound equally loud. b)
If you are using a handheld SPL meter with source material, such as c)
a test disc or an audio selection, play it and adjust the AVR’s master
volume control until the meter measures 75dB.
Press the AVR Settings Button to display the menu system, and then navigate
to the Speaker Setup line. Press the OK Button to display the Speaker Setup
menu. Select Setup Listening Position 1 (AVR 760, AVR 660) or 2 (AVR 760),
press the OK Button, and then navigate to the Level Adjust line. Press the OK
Button to display the Adjust Speaker Levels menu. See Figure 32.
Figure 32 – Adjust Speaker Levels Menu
All of the speaker channels will appear with their current level settings.
Reset Levels: To reset all levels to their factory defaults of 0dB, scroll down
to this line at the bottom of the menu and press the OK Button.
To set your levels using the AVR 760/AVR 660’s internal test tone, adjust the
TEST TONE line as follows:
Test Tone: Determines whether the test tone is active. To begin, press the
OK Button repeatedly to select the OFF, AUTO or MANUAL setting. Manually
moving the cursor out of the channel listings area of the screen automatically
stops the test tone.
When this setting reads AUTO, the test tone will automatically circulate to
all channels, pausing for a few moments at each channel and then moving
to the next channel several seconds later, as indicated by the highlight bar.
Adjust the level for any channel when the test tone is paused there, using the
M N Buttons. Use the KL Buttons to move the cursor to another line, and
the test tone will follow the cursor.
When this setting reads MANUAL, the test tone will not move to the next
channel until you use the
KL Buttons.
Individual Channels: If you are using an external source to set your
output levels, navigate to each channel and use the
M N Buttons to adjust
the level, as desired, between –10dB and +10dB.
When you have finished adjusting the speaker levels, select the Back option
or press the Back/Exit Button. Record the level settings in Table A3 in the
appendix.
auDIo effectS
To adjust other audio settings, such as the tone controls, to improve
performance, press the Audio Effects Button to display the Audio Effects
menu (see Figure 24 in the Basic Manual). The menu may also be accessed
from the Setup Source menu by pressing the Info Settings Button and
selecting Audio Effects.
NOTE: The settings in the Audio Effects menu affect each source
independently.
Dolby Volume: See page 30 of the Basic Manual for an explanation of
Dolby Volume processing and its benefits. Refer to Table 3 on that page for an
explanation of each of the Dolby Volume settings.
Tone Control: Determines whether the treble and bass controls are active.
When it’s off, the tone controls are “flat”, with no changes. When it’s on, the
bass and treble frequencies are boosted or cut, depending upon the tone-
control settings. When an analog audio source is in use and the 2-Channel
Stereo surround mode is selected, setting the Tone Control to “Off” places the
unit in analog bypass mode.
Treble and Bass: Boost or cut the high or low frequencies by up to 10dB
by using the
M N Buttons to change the temperature bar setting. The default
setting is 0dB, at the center of the temperature bar.
LFE Trim: Attenuates the loudness of the subwoofer. The setting defaults
to the maximum of 0dB. Press the
M N Buttons to reduce the level by up to
10dB; the setting will appear as a negative number.
EQ: This setting activates or deactivates the equalization settings obtained
when the EzSet/EQ II process was run. The settings are saved for reactivation
at a later listening session.
Speaker Setup: Select Position 1 (AVR 760, AVR 660) or 2 (AVR 760) to
activate the speaker configuration settings saved for the desired position.
The settings may be configured either by running the EzSet/EQ II process and
saving the results, or manually, as explained in the Manual Speaker Setup
section on page 6.
When you have finished, press the Audio Effects Button or the Back/Exit
Button.